Document revision date: 24 June 2002 | |
. . .
Term |
Definition |
---|---|
Operating
system CD–ROM |
The
CD–ROM containing the OpenVMS Alpha operating system. |
HSx device |
A
self-contained, intelligent, mass storage subsystem that lets computers in
an OpenVMS Cluster environment share disks. The disk on which you install
or upgrade the operating system can be connected to one of these systems
(for example, an HSC or HSD). |
InfoServer |
A
general-purpose disk storage server that allows you to use the operating system
CD–ROM to install the operating system on remote client systems connected
to the same local area network (LAN). |
Local
drive |
A
drive, such as an RRD42 CD–ROM drive, that is connected directly to
an Alpha computer. If you have a standalone Alpha computer, it is likely
that all drives connected to the system are local drives. |
Source
drive |
The
drive that holds the operating system CD–ROM during the upgrade or
installation. |
System
disk |
The
disk that contains (or will contain) the OpenVMS Alpha operating system.
The installation or upgrade procedure transfers the OpenVMS Alpha operating
system from the operating system CD–ROM on the source drive to the system
disk. |
Target
drive |
The
drive that holds the system disk during the upgrade or installation. |
CD–ROM
Label: |
OpenVMS
Alpha V7.3–1 Operating System |
Volume
Label: |
ALPHA0731 |
DKA400
DAD1
DKA0:
DUA20.14.0.2.0
OpenVMS (TM) Alpha Operating System, Version 7.3-1 Copyright (c) 2002 -- All rights reserved. Compaq Information Technologies, L.P. Installing required known files... Configuring devices... *************************************************************** You can install or upgrade the OpenVMS Alpha operating system or you can install or upgrade layered products that are included on the OpenVMS Alpha operating system CD-ROM. You can also execute DCL commands and procedures to perform "standalone" tasks, such as backing up the system disk. Please choose one of the following: 1) Upgrade, install or reconfigure OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system Enter CHOICE or ? for help: (1/2/3/4/5/6/7/8/?)
There are two choices for Installation/Upgrade: INITIALIZE - Removes all software and data files that were previously on the target disk and installs OpenVMS Alpha. PRESERVE -- Installs or upgrades OpenVMS Alpha on the target disk and retains all other contents of the target disk. * Note: You cannot use PRESERVE to install OpenVMS Alpha on a disk on which OpenVMS VAX or any other operating system is installed. Do you want to INITIALIZE or to PRESERVE? [PRESERVE]
IF
... |
THEN
... |
---|---|
the
OpenVMS Alpha operating system is not already
installed on the target disk, |
the
following operations take place: • The operating system is installed. • All other contents of the target disk
are retained. |
the
OpenVMS Alpha operating system is installed
on the target disk, |
the
operating system is upgraded, as
follows: • Old operating system files and new
files are merged or replaced. • All other contents of the target disk
are retained. |
Shutting down the system SYSTEM SHUTDOWN COMPLETE
IF
... |
THEN
... |
---|---|
you
want to install the operating system in an OpenVMS Cluster environment, |
|
you
want to install the operating system in a nonclustered environment, |
|
you
want to upgrade the operating system in any environment, |
|
you
want only to back up or restore your system disk, |
go
to Appendix B. |
Alpha
V7.3x and VAX V7.3 |
Alpha
V7.2-x1 (SEE NOTE) and
VAX V7.2 |
|
---|---|---|
Alpha
V7.3x and VAX V7.3 |
WARRANTED |
Migration |
Alpha
V7.2-x1 and VAX V7.2 |
Migration |
WARRANTED |
Required
Information |
Explanation |
---|---|
Type
of configuration |
Configuration
types (CI, DSSI, SCSI, local area, or mixed-interconnect) are distinguished
by the interconnect device that the VAX and Alpha computers in the OpenVMS
Cluster use to communicate with one another. |
DECnet
node name and node address |
See
the network or system manager to obtain the DECnet node name and node address
for the computer on which you are installing the OpenVMS Alpha operating system.
If you install DECnet-Plus for OpenVMS (Phase V) software and do not plan
to use DECnet Phase IV for OpenVMS addresses, then you do not need to provide
this information. |
Allocation
class value |
During
the installation procedure, you will be asked for the allocation class value
(ALLOCLASS) of the Alpha computer on which you are installing the OpenVMS
Alpha operating system. For example: Enter a value for this_node ALLOCLASS parameter: Refer
to OpenVMS Cluster Systems for the
rules on specifying allocation class values. Note that in a
mixed-interconnect OpenVMS Cluster environment, the allocation class value
cannot be zero if the nodes serve DSSI or CI disks. It must be a value from
1 to 255. This is also true for any Alpha computer that is connected to a
dual-pathed disk. After you enter the allocation class value, the
installation procedure uses it to automatically set the value of the ALLOCLASS
system parameter. |
Whether
you want a quorum disk |
Refer
to OpenVMS Cluster Systems to help
you determine whether you want a quorum disk in the cluster. |
Location
of the page and swap files |
On
a nonclustered system, the page and swap files are on one or more local disks
but on a clustered system, the files are on one or more local or clustered
disks. See OpenVMS Cluster Systems to
help you determine where the page and swap files will be located for the
system on which you are installing the OpenVMS Alpha operating system software. |
Systems
that will be MOP2 (SEE NOTE) servers,
disk servers, and tape servers |
If
you are going to set up either a local area or a mixed-interconnect cluster,
you will need to make these determinations. |
Cluster
group number and cluster password |
If
you are going to set up a local area cluster or a mixed-interconnect cluster
that is LAN-based, use the following rules to determine the cluster group
number and password: • Cluster group number — A number
in the range from 1 to 4095 or 61440 to 65535 • Cluster password — Must be from
1 to 31 alphanumeric characters in length and can include dollar signs ($)
and underscores(_) |
>>>SHOW DEVICE dva0.0.0.1000.0 DVA0 RX23 dka200.2.0.5.0 DKA200 RZ28M 1004 dka300.3.0.5.0 DKA300 RZ29B 0016 dka400.4.0.5.0 DKA400 RZ26L 442E ewa0.0.0.3.0 00-00-F8-1F-70-3D Twisted-Pair
Network Initial System Load Function Version 1.2 FUNCTION FUNCTION ID 1 - Display Menu 2 - Help 3 - Choose Service 4 - Select Options 5 - Stop Enter a function ID value:
IF ... |
THEN ... |
---|---|
you
previously chose the INITIALIZE option, |
do
the following: 1. Reboot the OpenVMS Alpha operating system
CD–ROM. 2. Choose the install option from the menu
and perform the installation again, as described in this chapter. |
you
previously chose the PRESERVE option, |
do
the following: 1. Reboot the OpenVMS Alpha operating system
CD–ROM. 2. Enter the DCL environment by choosing option
7 from the menu. 3. Mount the device containing your backup
copy of the target disk and the device that is your target disk. 4. Restore the backup copy of your target
disk by entering the appropriate BACKUP commands. (See Appendix
B for complete information using MOUNT and BACKUP commands to restore
a system disk.) 5. Log out from the DCL environment. 6. Choose the install option from the menu
and perform the installation again, as described in this chapter. |
OpenVMS (TM) Alpha Operating System, Version 7.3-1 Copyright (c) 2002 -- All rights reserved. Compaq Information Technologies Group, L.P. Installing required known files... Configuring devices... **************************************************************** You can install or upgrade the OpenVMS Alpha operating system or you can install or upgrade layered products that are included on the OpenVMS Alpha operating system CD-ROM. You can also execute DCL commands and procedures to perform "standalone" tasks, such as backing up the system disk. Please choose one of the following: 1) Upgrade, install or reconfigure OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system Enter CHOICE or ? for help: (1/2/3/4/5/6/7/8/?) 1
The following PATCH kits are present on the OpenVMS Alpha distribution media. ----------------------------------- ----------- ---------- PRODUCT KIT TYPE KIT FORMAT ----------------------------------- ----------- ---------- DEC AXPVMS DNVOSIECO01 V7.3 Patch Sequential DEC AXPVMS TCPIP_ECO V5.1-153 Patch Sequential DEC AXPVMS TCPIP_ECO V5.1-152 Patch Sequential DEC AXPVMS TCPIP_ECO V5.1-151 Patch Sequential DEC VAXVMS TCPIP_ECO V5.1-153 Patch Sequential DEC VAXVMS TCPIP_ECO V5.1-152 Patch Sequential DEC VAXVMS TCPIP_ECO V5.1-151 Patch Sequential ----------------------------------- ----------- ---------- 7 items found Please consult the OpenVMS Alpha Upgrade and Installation Manual, the Release Notes, and the Cover Letter to determine if any or all of these patches may be required for your system.
IF
... |
THEN
... |
---|---|
your
system disk is new, |
do
the following: 1. Enter INITIALIZE. 2. Press the Return key. |
you
want to remove all files from an existing system disk, |
do
the following: 1. Enter INITIALIZE. 2. Press the Return key. |
you
want to retain certain files on an existing disk, |
press
the Return key to accept the default (PRESERVE). |
MKA500 is not a disk device
Enter volume label for target system disk: [ALPHASYS] The target system disk can be initialized with On-Disk Structure Level 2 (ODS-2) or Level 5 (ODS-5). (? for more information) Do you want to initialize with ODS-2 or ODS-5? (2/5/?)
Hard links can be enabled on ODS-5 disks. (? for more information) (***Enabling hard links can take up to 5-10 minutes or more.***) Do you want to enable hard links? (Yes/No)
You have chosen to install OpenVMS Alpha on a new disk. The target system disk, DKB400:, will be initialized with structure level 5 (ODS-5). Hard links will NOT be enabled. It will be labeled ALPHASYS. Any data currently on the target system disk will be lost. Is this OK? (Yes/No) Y Initializing and mounting target.... Creating page and swap files....
You must enter a password for the SYSTEM account. The password must be a minimum of 8 characters in length, and may not exceed 31 characters. It will be checked and verified. The system will not accept passwords that can be guessed easily. The password will not be displayed as you enter it. Password for SYSTEM account: Reenter SYSTEM password for verification:
Will this system be a member of an OpenVMS Cluster? (Yes/No) Yes
Will this system be an instance in an OpenVMS Galaxy? (Yes/No) Yes
You can install the following products along with the OpenVMS operating system: o DECwindows Motif for OpenVMS Alpha o DECnet-Plus for OpenVMS Alpha o DECnet Phase IV for OpenVMS Alpha o Compaq TCP/IP Services for OpenVMS If you want to change your selections, you can do so later in the installation by answering "NO" to the following question: "Do you want the defaults for all product options?" Do you want to install DECwindows Motif for OpenVMS Alpha V1.2-6? (Yes/No) [YES] y Beginning with OpenVMS V7.1, the DECnet-Plus kit is provided with the OpenVMS operating system kit. Compaq recommends that DECnet users install DECnet-Plus. DECnet Phase IV applications are supported by DECnet-Plus. DECnet Phase IV is also provided as an option. Support for DECnet Phase IV is available through a Prior Version Support Contract available through Compaq’s Services. If you install DECnet-Plus and TCP/IP you can run DECnet applications over a TCP/IP network. Please see the OpenVMS Management Guide for information on running DECnet over TCP/IP. Do you want to install DECnet-Plus for OpenVMS Alpha V7.3-1? (Yes/No) [YES] y Do you want to install Compaq TCP/IP Services for OpenVMS V5.1? (Yes/No) [YES] n
For your system to operate properly, you must set two parameters: SCSNODE and SCSSYSTEMID. SCSNODE can be from 1 to 6 letters or numbers. It must contain at least one letter. If you plan to use DECnet, SCSNODE must be the DECnet Phase IV node name, or the DECnet-Plus node synonym. If you have multiple OpenVMS systems, the SCSNODE on each system must be unique. Enter SCSNODE: alpcsi If you plan to use DECnet, SCSSYSTEMID must be set based on the DECnet Phase IV address. DECnet Phase IV addresses are in the format DECnet_area_number.DECnet_node_number DECnet_area_number is a number between 1 and 63. DECnet_node_number is a number between 1 and 1023. If you plan to use DECnet WITHOUT Phase IV compatible addresses, enter 0.0. Enter DECnet (Phase IV) Address [1.1]: 63.180 SCSSYSTEMID will be set to 64692. This was calculated as follows: (DECnet_area_number * 1024) + DECnet_node_number
Please choose a SCSSYSTEMID between 1 and 65535. If you have multiple OpenVMS systems, the SCSSYSTEMID on each system must be unique. Enter SCSYSTEMID [65535]: 12345
Configuring the Local Time Zone TIME ZONE SPECIFICATION -- MAIN Time Zone Menu 1) AFRICA 16) GREENWICH 31) POLAND 2) AMERICA 17) HONGKONG 32) PRC 3) ANTARCTICA 18) ICELAND 33) ROC 4) ASIA 19) INDIAN 34) ROK 5) ATLANTIC 20) IRAN 35) SINGAPORE 6) AUSTRALIA 21) ISRAEL 36) SYSTEMV 7) BRAZIL 22) JAMAICA 37) TURKEY 8) CANADA 23) JAPAN 38) UCT 9) CET 24) LIBYA 39) UNIVERSAL 10) CHILE 25) MET 40) US 11) CUBA 26) MEXICO 41) UTC 12) EET 27) NAVAJO 42) W-SU 13) EGYPT 28) NZ-CHAT 43) WET 14) FACTORY 29) NZ 44) ZULU 15) GB-EIRE 30) PACIFIC 0) GMT Select the number above that best represents the desired time zone: 40 US Time Zone Menu 1) ALASKA 5) EAST-INDIANA 9) MICHIGAN 2) ALEUTIAN 6) EASTERN 10) MOUNTAIN 3) ARIZONA 7) HAWAII 11) PACIFIC 4) CENTRAL 8) INDIANA-STARKE 12) SAMOA 0) return to Main Time Zone Menu Select the number above that best represents the desired time zone: 6 You selected EASTERN / US as your time zone. Is this correct? (Yes/No) [YES]: Configuring the Time Differential Factor (TDF) Default Time Differential Factor for standard time is -5:00. Default Time Differential Factor for daylight saving time is -4:00. The Time Differential Factor (TDF) is the difference between your system time and Coordinated Universal Time (UTC). UTC is similar in most respects to Greenwich Mean Time (GMT). The TDF is expressed as hours and minutes, and should be entered in the hh:mm format. TDFs for the Americas will be negative (-3:00, -4:00, etc.); TDFs for Europe, Africa, Asia and Australia will be positive (1:00, 2:00, etc.). This time zone supports daylight saving time. Is this time zone currently on daylight saving time? (Yes/No): n Enter the Time Differential Factor [-5:00]: NEW SYSTEM TIME DIFFERENTIAL FACTOR = -5:00 Is this correct? [Y]:
Do you want to register any Product Authorization Keys?
Type
of License |
Description |
---|---|
Operating
System Base License |
Grants
the right to noninteractive use of the remote batch, print, application,
and computing services of the operating system on a single processor and
authorizes one direct login (for system management purposes only). This license
is a prerequisite for OpenVMS Alpha Interactive User Licenses. |
Interactive
User Licenses |
Grant
the right to interactive use of the OpenVMS Alpha operating system, provided
you have previously installed the appropriate OpenVMS Alpha Operating System
Base License on your Alpha computer. These licenses, which are concurrent,
are available in any quantity desired or as an unlimited user license. You
can add interactive users to the computer at any time by specifying the same
node name on the additional Interactive User License PAK and by following
the license combination procedure described in the OpenVMS
License Management Utility Manual. |
Symmetric
Multiprocessing (SMP) Extension to the Operating System Base License |
Upgrades
the Operating System Base License and all Interactive User licenses (including
Unlimited) to the matching multiprocessing level of your Alpha SMP system. Because
the Symmetric Multiprocessing (SMP) Extension grants all the rights the existing
Base and User licenses provided at the uniprocessing level, you do not need
to reinstall those licenses when you upgrade to a multiprocessing system.
Each time you upgrade your system to a new multiprocessing level (for example,
from a DEC 7000 Model 620 Alpha system to a DEC 7000 Model 630 Alpha system),
you add an SMP Extension to your existing licenses. |
If you have Product Authorization Keys (PAKs) to register, you can register them now. Do you want to register any Product Authorization Keys? (Yes/No) [Yes]
IF
... |
THEN
... |
---|---|
you
choose to register your licenses at this time (which Compaq recommends), |
do
the following: 1. Be sure you review Appendix
C and have the OpenVMS License Management
Utility Manual available. 2. Be sure you have a copy of the Product
Authorization Key (PAK) for each license that you will register. 3. Type Y and press the Return key. 4. Register your licenses, as described in
the next section. |
you
choose not to register your licenses
at this time, |
do
the following: 1. Type N and press the Return key. 2. Skip the next section about registering
licenses and follow the directions in Section 3.5. 3. After completing the installation, register
your licenses using the LICENSE REGISTER command or by invoking SYS$UPDATE:VMSLICENSE.COM before performing any other postinstallation
tasks. |
VMS License Management Utility Options: 1. REGISTER a Product Authorization Key 2. AMEND an existing Product Authorization Key 3. CANCEL an existing Product Authorization Key 4. LIST Product Authorization Keys 5. MODIFY an existing Product Authorization Key 6. DISABLE an existing Product Authorization Key 7. DELETE an existing Product Authorization Key 8. COPY an existing Product Authorization Key 9. MOVE an existing Product Authorization Key 10. ENABLE an existing Product Authorization Key 11. SHOW the licenses loaded on this node 12. SHOW the unit requirements for this node 99. Exit this procedure Type ’?’ at any prompt for a description of the information requested. Press Ctrl/Z at any prompt to return to this menu. Enter one of the above choices [1]
The installation can provide brief or detailed descriptions. In either case, you can request the detailed descriptions by typing "?". Do you always want detailed descriptions? (Yes/No) [No]
The following product has been selected: DEC AXPVMS OPENVMS V7.3-1 Platform (product suite) Configuration phase starting ... You will be asked to choose options, if any, for each selected product and for any products that may be installed to satisfy software dependency requirements. DEC AXPVMS OPENVMS V7.3-1: OpenVMS and related products Platform COPYRIGHT (c) 27-MAY-2002 -- All rights reserved Compaq Information Technologies Group, L.P.
Do you want the defaults for all options? [YES]
Accounting Log Report Generator Utility Access Control List Utilities Print and Batch Queue Utilities DECdtm Distributed Transaction Manager LDAP (Lightweight Directory Access Protocol) files Support for DECnet-Plus or DECnet for OpenVMS DECnet Incoming Remote File Access DECnet Incoming Remote Terminal DECnet Network Test DECnet Remote Task Loading Programming Support Debugger Utility Image Dump Utility RMS Analyze and FDL Editor Utilities Message Utility System Shareable Image and Object Module Libraries Macro libraries Macro-32 Migration Compiler TLB intermediary form of STARLET Fortran Require Files C Object Libraries C Header Files VMS text libraries of Ada declarations RMS Journaling Recovery Utility System Programming Support Support for ISO 9660 and High Sierra CDrom Formats MONITOR Analyze Object File Utility Delta Debugger System Dump Analyzer Utility Miscellaneous Symbol Table Files OpenVMS Management Station Software -- PC files Utilities OpenVMS Mail Utility Dump Utility DIGITAL Standard Runoff (DSR) Text Formatter Phone Utility Help Library Foreign Terminal Support LAT-11 Terminal Server (via Ethernet) Error Log Generator Utility Terminal Fallback Facility TECO Interactive Text Editor National Character Set Utility (NCS) DIAGNOSE Utility XPG4 Internationalization Utilities World Wide PostScript Printing Subsystem Bliss Require Files Example Files Message Facility Files (HELP/MESSAGE) Translated Image Support UETP Files Support for DECwindows DECwindows workstation files Video fonts 100 dots-per-inch video fonts Delete any obsolete OpenVMS files Delete files archived by OpenVMS remedial kits
%PMA0 CPU00: 30-MAY-2002 14:58:40 Remote System Conflicts with Known System - REMOTE NODE %PMA0 CPU00: 30-MAY-2002 14:58:45 Remote System Conflicts with Known System - REMOTE NODE
Do you want to review the options? [NO] Execution phase starting ... The following products will be installed to destinations: CPQ AXPVMS CDSA V1.0 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS DECNET_OSI V7.3-1 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS DWMOTIF V1.2-6 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS OPENVMS V7.3-1 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS TCPIP V5.1 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS VMS V7.3-1 DISK$ALPHASYS:[VMS$COMMON.] Portion done: 0%..10%..20%..30%..40%..50%..60%..70%..80%..90%..100% The following products have been installed: CPQ AXPVMS CDSA V1.0 Layered Product DEC AXPVMS DECNET_OSI V7.3-1 Layered Product DEC AXPVMS DWMOTIF V1.2-6 Layered Product DEC AXPVMS OPENVMS V7.3-1 Platform (product suite) DEC AXPVMS TCPIP V5.1 Layered Product DEC AXPVMS VMS V7.3-1 Operating System The installation is now complete. When the newly installed system is first booted, a special startup procedure will be run. This procedure will: o Configure the system for standalone or OpenVMS Cluster operation. o Run AUTOGEN to set system parameters. o Reboot the system with the newly set parameters. You may shut down now or continue with other operations. Process AXPVMS_INSTALL logged out at 27-MAY-2002 14:45:49.54 Press Return to continue... **************************************************************** You can install or upgrade the OpenVMS Alpha operating system or you can install or upgrade layered products that are included on the OpenVMS Alpha operating system CD-ROM. You can also execute DCL commands and procedures to perform "standalone" tasks, such as backing up the system disk. Please choose one of the following: 1) Install or upgrade OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system Enter CHOICE or ? for help: (1/2/3/4/5/6/7/8/?)
DEC AXPVMS UCX V4.2-PLACEHOLDER
The UCX implementation of TCP/IP Services is obsolete and is not supported on OpenVMS V7.2 and higher versions. Starting with OpenVMS V7.2, the UCX implementation of TCP/IP services is replaced by the new TCPIP product. This is a placeholder kit to satisfy OpenVMS upgrade requirements so that UCX can be automatically upgraded to TCPIP. You cannot use this kit to install UCX.
DEC AXPVMS TCPIP V5.1
OpenVMS (TM) Alpha Operating System, Version 7.3-1 %DECnet-I-LOADED, network base image loaded, version = 05.0D.00 $! Copyright (c) 2002 Compaq Information Technologies Group, L.P. $! All rights reserved. Installing required known files... Configuring devices... . . .
Question |
How
to Respond |
---|---|
Will
this node be a cluster member (Y/N)? |
Enter
Y. |
What
is the node’s DECnet node name? |
Enter
the DECnet node name (for example, MYNODE). The DECnet node name may be from
one to six alphanumeric characters in length and cannot include dollar signs
or underscores. |
What
is the node’s DECnet node address? |
Enter
the DECnet node address --- for example, 2.2. |
Will
the Ethernet be used for cluster communications (Y/N)? |
Enter
N for a CI only or DSSI-only OpenVMS Cluster. Otherwise, answer Y. 2
(SEE NOTE) |
Enter
this cluster’s group number: |
Enter
a number in the range from 1 to 4095 or 61440 to 65535. |
Enter
this cluster’s password: |
Enter
the cluster password. The password must be from 1 to 31 alphanumeric characters
in length and may include dollar signs and underscores.3
(SEE NOTE) |
Reenter
this cluster’s password for verification: |
Reenter
the password. |
Will
MYNODE be a disk server (Y/N)? |
Enter
Y if you want local disks to be served to the cluster (mandatory for local
area and mixed-interconnect configurations). Refer to OpenVMS
Cluster Systems for information about served cluster disks. |
Will
MYNODE serve RFxx disks (Y)? |
Enter
a response appropriate for your DSSI configuration, if such disks are available
to your system. |
Enter
a value for MYNODE’s ALLOCLASS parameter: |
In
a CI only system (connected to a dual-ported disk), a DSSI-only system, or
a local area or mixed-interconnect configuration where nodes serve DSSI or
CI disks, enter the appropriate allocation class value (1 to 255). Otherwise,
enter 0. For information about selecting the ALLOCLASS parameter, see OpenVMS Cluster Systems. |
Does
this cluster contain a quorum disk (Y/N)? |
For
CI only, SCSI, local area, and mixed-interconnect configurations, enter Y
or N, depending on your configuration. For most DSSI systems, enter Y. However, if you
are adding a two-system DSSI configuration to an existing cluster (in which
case you might not need a quorum disk), you can answer N. If you
enter Y, the system asks for the name of the quorum disk. Enter the device
name of the quorum disk. Refer to OpenVMS
Cluster Systems for information about quorum disks. |
AUTOGEN will now be run to compute the new SYSGEN parameters. The system will then shut down and reboot, and the installation or upgrade will be complete. After rebooting you can continue with such system management tasks as: Decompressing the System Libraries Configuring DECnet Using SYS$MANAGER:CLUSTER_CONFIG.COM to create an OpenVMS Cluster Creating FIELD, SYSTEST, and SYSTEST_CLIG accounts if needed %AUTOGEN-I-BEGIN, GETDATA phase is beginning. %AUTOGEN-I-NEWFILE, A new version of SYS$SYSTEM:PARAMS.DAT has been created. You may wish to purge this file. %AUTOGEN-I-END, GETDATA phase has successfully completed. %AUTOGEN-I-BEGIN, GENPARAMS phase is beginning. %AUTOGEN-I-NEWFILE, A new version of SYS$MANAGER:VMSIMAGES.DAT has been created. You may wish to purge this file. %AUTOGEN-I-NEWFILE, A new version of SYS$SYSTEM:SETPARAMS.DAT has been created. You may wish to purge this file. %AUTOGEN-I-END, GENPARAMS phase has successfully completed. %AUTOGEN-I-BEGIN, GENFILES phase is beginning. %SYSGEN-I-EXTENDED, SYS$SYSROOT:[SYSEXE]PAGEFILE.SYS;1 extended %SYSGEN-I-EXTENDED, SYS$SYSROOT:[SYSEXE]SWAPFILE.SYS;1 extended %SYSGEN-I-CREATED, SYS$SYSROOT:[SYSEXE]SYSDUMP.DMP;1 created %AUTOGEN-I-REPORT, AUTOGEN has produced some informational messages that have been stored in the file SYS$SYSTEM:AGEN$PARAMS.REPORT. You may wish to review the information in that file. %AUTOGEN-I-END, GENFILES phase has successfully completed. %AUTOGEN-I-BEGIN, SETPARAMS phase is beginning. . . .
The system is shutting down to allow the system to boot with the generated site-specific parameters and installed images. The system will automatically reboot after the shutdown and the installation will be complete. SHUTDOWN -- Perform an Orderly System Shutdown on node ALPCSI %SHUTDOWN-I-BOOTCHECK, performing reboot consistency check... %SHUTDOWN-I-CHECKOK, basic reboot consistency check completed . . .
OpenVMS (TM) Alpha Operating System, Version 7.3-1 Copyright (c) 2002 -- All rights reserved. Compaq Information Technologies Group, L.P. %STDRV-I-STARTUP, OpenVMS startup begun at 27-MAY-2002 14:50:18.35 . . .
%SET-I-INTSET, login interactive limit = 64, current interactive value = 0 SYSTEM job terminated at 27-MAY-2002 14:51:23.47 Accounting information: Buffered I/O count: 2177 Peak working set size: 6848 Direct I/O count: 1358 Peak page file size: 179552 Page faults: 1805 Mounted volumes: 0 Charged CPU time: 0 00:00:13.37 Elapsed time: 0 00:01:06.20
$ @SYS$STARTUP:CDSA$INITIALIZE
$ @SYS$STARTUP:KRB$STARTUP.COM
$ @SYS$MANAGER:KRB$SYMBOLS
$ @SYS$STARTUP:KRB$CONFIGURE.COM
!$ SUBMIT SYS$MANAGER:STARTNET.COM
$! DECNET_VERSION = F$INTEGER(F$EXTRACT(2,2,F$GETSYI("DECNET_VERSION") ) ) $! IF DECNET_VERSION .GE. 5 $! THEN $! START/NETWORK "DECNET/OSI"$! ELSE $! START/NETWORK DECNET $! ENDIF
Library
Name |
Reduced
Size (as shipped) |
Expanded
Size |
Description |
---|---|---|---|
[SYSHLP] directory; Help library files (.HLB) |
ACLEDT.HLB |
70 |
102 |
Access
Control List Editor help |
BKM$HELP.HLB |
156 |
248 |
Backup
Manager help |
DBG$HELP.HLB |
1234 |
2133 |
OpenVMS
Debugger help |
DBG$UIHELP.HLB |
269 |
438 |
OpenVMS
Debugger help |
EDTHELP.HLB |
154 |
229 |
EDT
Editor help |
EVE$HELP.HLB |
676 |
1197 |
EVE
Editor help |
EVE$KEYHELP.HLB |
99 |
145 |
EVE
Keypad help |
EXCHNGHLP.HLB |
83 |
118 |
Exchange
Utility help |
HELPLIB.HLB |
9179 |
16662 |
DCL
help |
LANCP$HELP.HLB |
119 |
174 |
LAN
Control Program help |
LATCP$HELP.HLB |
157 |
243 |
LAT
Control Program help |
MAILHELP.HLB |
211 |
316 |
Mail
Utility help |
NCPHELP.HLB |
261 |
412 |
Network
Control Program help |
SDA.HLB |
308 |
457 |
System
Dump Analyzer help |
SHWCLHELP.HLB |
103 |
151 |
Show
Cluster utility help |
SYSGEN.HLB |
337 |
526 |
System
Generation utility help |
SYSMANHELP.HLB |
492 |
786 |
System
Management utility help |
TPUHELP.HLB |
575 |
1036 |
Text
Processing Utility help |
UAFHELP.HLB |
241 |
377 |
Authorize
Utility help |
[SYSLIB] directory; Macro library files (.MLB) |
LANIDEF.MLB |
181 |
241 |
LAN
internal driver macros |
LIB.MLB |
2715 |
4679 |
Operating
system macros |
STARLET.MLB |
2335 |
3467 |
Operating
system macros |
[SYSLIB] directory; Object library files (.OLB)
|
STARLET.OLB |
27461 |
44256 |
System
object library and run-time library |
VAXCRTL.OLB |
1163 |
1557 |
Compaq
C RTL routine name entry points; VAX G_floating double-precision, floating-point
entry points |
VAXCRTLD.OLB |
1587 |
2542 |
Limited
support of VAX D_floating double-precision, floating-point entry points |
VAXCRTLDX.OLB |
1506 |
2391 |
VAX
D_floating support; support for /L_DOUBLE_SIZE=128 compiler qualifier |
VAXCRTLT.OLB |
1434 |
2234 |
IEEE
T_floating double-precision, floating-point entry points |
VAXCRTLTX.OLB |
1449 |
2244 |
IEEE
T_floating support; support for /L_DOUBLE_SIZE=128 compiler qualifier |
VAXCRTLX.OLB |
1285 |
1811 |
G_floating
support; support for /L_DOUBLE_SIZE=128 compiler qualifier |
VMS$VOLATILE_ PRIVATE_INTERFACES.OLB |
445 |
635 |
OpenVMS
bugcheck processing codes |
[SYSLIB] directory; Text library files (.TLB) |
ERFLIB.TLB |
64 |
85 |
ANALYZE/ERROR
device descriptions |
LIB_ADA_SUBSET.TLB |
1839 |
3385 |
Ada
programmers toolkit of operating system definitions |
NTA.TLB |
34 |
42 |
Files
to build against NTA facility |
STARLET_RECENT_ ADA_SUBSET.TLB |
1100 |
1942 |
Ada
programmers toolkit of operating system definitions |
STARLETSD.TLB |
3940 |
7208 |
STARLET
definitions used during layered product installations |
SYS$LIB_C.TLB |
9442 |
20214 |
Header
files for C language; derived from LIB |
SYS$STARLET_C.TLB |
5864 |
12752 |
Public
header files for Compaq C |
TOTALS: |
78568 |
137435 |
Please choose one of the following: 1) Upgrade, install or reconfigure OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system Enter CHOICE or ? for help: (1/2/3/4/5/6/7/8/?) 1 *********************************************************** . . . Do you want to INITIALIZE or to PRESERVE? [PRESERVE] . . . Version 7.3-1 of the OpenVMS operating system is already installed on the target disk. You may choose one of the following actions: o Reconfigure the OpenVMS platform. This action will allow you to change your selections of which of the windowing and network products you included with your OpenVMS operating system installation. o Reconfigure the OpenVMS operating system. This action will allow you to change your choices about which options you included for the OpenVMS operating system. o Reinstall the OpenVMS operating system. This action will cause ALL operating system files to be replaced. You can also change your choices about which options you included for the OpenVMS operating system. Reinstall will take longer than Reconfigure. Reinstall may be appropriate if you suspect that files in the operating system, or in the windowing and network products have become corrupted. If you want to reinstall any of the windowing and network products, choose "Install or upgrade layered products and patches" (option 3) from the main menu. If you want to change your choices about which options you included for any of the windowing and network products, choose "Reconfigure installed products" (option 5) from the main menu. Please choose one of the following: 1) Reconfigure the OpenVMS platform. 2) Reconfigure the OpenVMS operating system. 3) Reinstall the OpenVMS operating system. 4) Return to the Main Menu (abort the upgrade/installation). Enter choice or ? for help: (1/2/3/4/?) 2 The following product has been selected: DEC AXPVMS VMS V7.3-1 Operating System Configuration phase starting ... You will be asked to choose options, if any, for each selected product and for any products that may be installed to satisfy software dependency requirements. DEC AXPVMS VMS V7.3-1: OpenVMS Operating System COPYRIGHT (c) 12-MAY-2002 -- All rights reserved Compaq Information Technologies Group, L.P. Do you want the defaults for all options? [YES]
Do you want to review the options? [NO] Execution phase starting ... The following product will be reconfigured: DEC AXPVMS VMS V7.3-1 Portion done: 0%...10%...20%...30%...40%...50%...60%...80%...90%...100% The following product has been reconfigured: DEC AXPVMS VMS V7.3-1 . . .
CPU |
Operating
System |
Client
Kit |
---|---|---|
Alpha |
Windows
NT |
40COMAXP.EXE |
Intel |
Windows
NT |
40COMUPD.EXE |
Alpha |
Windows
NT |
DEBUGALPHA011.EXE |
Intel |
Windows
95, 98, Me, NT, 2000, XP |
DEBUGX86011.EXE |
Install
Option |
Details |
---|---|
Typical |
Debug
client and OpenVMS Debugger Manual
in HTML format |
Compact |
Debug
client only |
Custom |
Choice
of Debug Client and/or OpenVMS Debugger
Manual in HTML format |
System
Parameter |
Default
Value |
---|---|
NPAG_BAP_MIN |
0 |
NPAG_BAP_MAX |
0 |
NPAG_BAP_MIN_PA |
0 |
NPAG_BAP_MAX_PA |
-1 |
$ @SYS$UPDATE:AUTOGEN SAVPARAMS SETPARAMS FEEDBACK
$ @SYS$SYSTEM:AGEN$FEEDBACK.EXE
$ SEARCH SYS$SYSTEM:AGEN$FEEDBACK.DAT "BAP_"
AGEN$FEEDBACK Data |
System Parameter |
Units |
---|---|---|
BAP_MIN |
NPAG_BAP_MIN |
bytes |
BAP_MAX |
NPAG_BAP_MAX |
bytes |
BAP_MIN_PA |
NPAG_BAP_MIN_PA |
Mbytes1
(SEE NOTE) |
BAP_MAX_PA |
NPAG_BAP_MAX_PA |
Mbytes1 |
%ANALDISK-I-OPENQUOTA, error opening QUOTA.SYS
$ DIRECTORY/FILE_ID/NOHEADING/NOTRAILING device:[000000]VMS$COMMON.DIR $ DIRECTORY/FILE_ID/NOHEADING/NOTRAILING device:[SYS*]SYSCOMMON.DIR
$ DIRECTORY/FILE_ID/NOHEADING/NOTRAILING SYS$SYSDEVICE:[000000]VMS$COMMON.DIR $ DIRECTORY/FILE_ID/NOHEADING/NOTRAILING SYS$SYSDEVICE:[SYS*]SYSCOMMON.DIR
$ DIRECTORY/FILE_ID/NOHEADING/NOTRAILING DKA100:[000000]VMS$COMMON.DIR $ DIRECTORY/FILE_ID/NOHEADING/NOTRAILING DKA100:[SYS*]SYSCOMMON.DIR
ADD_GBLPAGES=128
$ SYS$UPDATE:AUTOGEN SAVPARAMS
IF
... |
THEN
... |
---|---|
you
are upgrading a standalone system, |
do
the following: 1. Log in to the SYSTEM account. 2. Enter
the following command and then press the Return key: 3. When the procedure asks if an automatic
system reboot should be performed, enter N (No) and press the Return key.
4. Go to the checklist at the end of this
chapter to verify that you have performed the necessary tasks; then go to Chapter 7, Upgrading
the OpenVMS Alpha Operating System to begin the upgrade procedure. |
you
are upgrading an OpenVMS Cluster system, |
do
the following: 1. Review the checklist at the end of this
chapter. |
Alpha
V7.3x and VAX V7.3 |
Alpha
V7.2-x1 (SEE NOTE) and
VAX V7.2 |
|
---|---|---|
Alpha
V7.3x and VAX V7.3 |
WARRANTED |
Migration |
Alpha
V7.2-x1 and VAX V7.2 |
Migration |
WARRANTED |
>>>SHOW DEVICE dva0.0.0.1000.0 DVA0 RX23 dka200.2.0.5.0 DKA200 RZ28M 1004 dka300.3.0.5.0 DKA300 RZ29B 0016 dka400.4.0.5.0 DKA400 RZ26L 442E ewa0.0.0.3.0 00-00-F8-1F-70-3D Twisted-Pair
Network Initial System Load Function Version 1.2 FUNCTION FUNCTION ID 1 - Display Menu 2 - Help 3 - Choose Service 4 - Select Options 5 - Stop Enter a function ID value:
OpenVMS (TM) Alpha Operating System, Version 7.3-1 Copyright (c) 2002 -- All rights reserved. Compaq Information Technologies Group, L.P. Installing required known files... Configuring devices... **************************************************************** You can install or upgrade the OpenVMS Alpha operating system or you can install or upgrade layered products that are included on the OpenVMS Alpha operating system CD-ROM. You can also execute DCL commands and procedures to perform "standalone" tasks, such as backing up the system disk. Please choose one of the following: 1) Upgrade, install or reconfigure OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system Enter CHOICE or ? for help: (1/2/3/4/5/6/7/8/?) 1
The following PATCH kits are present on the OpenVMS Alpha distribution media. ----------------------------------- ----------- ---------- PRODUCT KIT TYPE KIT FORMAT ----------------------------------- ----------- ---------- DEC AXPVMS DNVOSIECO01 V7.3 Patch Sequential DEC AXPVMS TCPIP_ECO V5.1-153 Patch Sequential DEC AXPVMS TCPIP_ECO V5.1-152 Patch Sequential DEC AXPVMS TCPIP_ECO V5.1-151 Patch Sequential DEC VAXVMS TCPIP_ECO V5.1-153 Patch Sequential DEC VAXVMS TCPIP_ECO V5.1-152 Patch Sequential DEC VAXVMS TCPIP_ECO V5.1-151 Patch Sequential ----------------------------------- ----------- ---------- 7 items found Please consult the OpenVMS Alpha Upgrade and Installation Manual, the Release Notes, and the Cover Letter to determine if any or all of these patches may be required for your system.
MKA500 is not a disk device
DKB400: is now labeled ALPHASYS. Do you want to keep this label? (Yes/No)
Do you want to convert the target system disk to ODS-5? (Yes/No/?) No OpenVMS Alpha will be upgraded on DKB400:.
Do you want to convert the target system disk to ODS-5? (Yes/No/?) Yes DKB400: has been converted to ODS-5. Information on converting ODS-5 disks back to ODS-2 can be found in the Compaq OpenVMS System Manager’s Manual. Hard links can be enabled on ODS-5 disks. (? for more information) (***Enabling hard links can take up to 5-10 minutes or more.***) Do you want to enable hard links? (Yes/No)
Hard links have been enabled on DKB400:. OpenVMS Alpha will be upgraded on DKB400:.
Either SPIRALOG is installed or SYS$SYSTEM:SPIRALOG.EXE is present on the target system. SPIRALOG is no longer supported; it will not work and can cause serious problems that are difficult to diagnose. If installed, SPIRALOG must be removed before upgrading. If SPIRALOG is not installed but SYS$SYSTEM:SPIRALOG.EXE is present on the target system, this file must be deleted in order to prevent the upgraded system from generating errors. (Check common and specific directories for SPIRALOG.EXE.) Termination is strongly recommended. Do you want to terminate? (Yes/No) [YES]
The target system contains a version of DECamds that is not compatible with this version of the operating system. If you continue DECamds will be removed. A current version of DECamds can be installed after the upgrade completes.
PATHWORKS V5 is installed on the target system. This version of PATHWORKS will not work on OpenVMS V7.3-1. Before you upgrade OpenVMS you must either upgrade to a supported version of PATHWORKS or migrate to Advanced Server. Please refer to the PATHWORKS or Advanced Server installation guides for additional information. Do you want to continue? (Yes/No) [NO]
Will this system be a member of an OpenVMS Cluster? (Yes/No) Yes
Will this system be an instance in an OpenVMS Galaxy? (Yes/No) Yes
If necessary, the following products will be upgraded along with the OpenVMS operating system: o DECwindows Motif for OpenVMS Alpha o DECnet-Plus for OpenVMS Alpha o DECnet Phase IV for OpenVMS Alpha o Compaq TCP/IP Services for OpenVMS If you want to add or delete these products, you can do so later in the upgrade by answering NO to the following question: "Do you want the defaults for all product options?" Beginning with OpenVMS V7.1, DECnet-Plus is provided with the OpenVMS operating system. Compaq recommends that DECnet users install DECnet-Plus. DECnet Phase IV applications are supported by DECnet-Plus. DECnet Phase IV is also provided as an option. Support for DECnet Phase IV is available through a Prior Version Support Contract available through Compaq Services. Once you have DECnet-Plus and TCP/IP installed on your system, you can run DECnet applications over your TCP/IP network. Please see the DECnet-Plus for OpenVMS Management Guide for more information on DECnet over TCP/IP. Do you want to install DECnet-Plus for OpenVMS Alpha V7.3-1? (Yes/No) [YES] n DECnet Phase IV for OpenVMS Alpha is installed on your system. It will be upgraded. Beginning with OpenVMS V7.2, a new implementation of Compaq TCP/IP Services became available. This new implementation replaces the UCX product. Older, UCX version of Compaq TCP/IP Services for OpenVMS can be upgraded to this new implementation. Compaq TCP/IP Services for OpenVMS is not installed on your system. It will not be installed.
DECwindows Motif is already installed. You can keep the installed version or upgrade to V1.2-6. Do you want to upgrade to V1.2-6? (Yes/No) [YES]
[VMS$COMMON.SYSEXE]SYS$TIMEZONE.DAT [VMS$COMMON.SYSEXE]SYS$TIMEZONE_SRC.DAT [VMS$COMMON.SYS$STARTUP]TDF$UTC_STARTUP.COM
Configuring the Local Time Zone TIME ZONE SPECIFICATION -- MAIN Time Zone Menu 1) AFRICA 16) GREENWICH 31) POLAND 2) AMERICA 17) HONGKONG 32) PRC 3) ANTARCTICA 18) ICELAND 33) ROC 4) ASIA 19) INDIAN 34) ROK 5) ATLANTIC 20) IRAN 35) SINGAPORE 6) AUSTRALIA 21) ISRAEL 36) SYSTEMV 7) BRAZIL 22) JAMAICA 37) TURKEY 8) CANADA 23) JAPAN 38) UCT 9) CET 24) LIBYA 39) UNIVERSAL 10) CHILE 25) MET 40) US 11) CUBA 26) MEXICO 41) UTC 12) EET 27) NAVAJO 42) W-SU 13) EGYPT 28) NZ-CHAT 43) WET 14) FACTORY 29) NZ 44) ZULU 15) GB-EIRE 30) PACIFIC 0) GMT Select the number above that best represents the desired time zone: 40 US Time Zone Menu 1) ALASKA 5) EAST-INDIANA 9) MICHIGAN 2) ALEUTIAN 6) EASTERN 10) MOUNTAIN 3) ARIZONA 7) HAWAII 11) PACIFIC 4) CENTRAL 8) INDIANA-STARKE 12) SAMOA 0) return to Main Time Zone Menu Select the number above that best represents the desired time zone: 6 You selected EASTERN / US as your time zone. Is this correct? (Yes/No) [YES]: Configuring the Time Differential Factor (TDF) Default Time Differential Factor for standard time is -5:00. Default Time Differential Factor for daylight saving time is -4:00. The Time Differential Factor (TDF) is the difference between your system time and Coordinated Universal Time (UTC). UTC is similar in most respects to Greenwich Mean Time (GMT). The TDF is expressed as hours and minutes, and should be entered in the hh:mm format. TDFs for the Americas will be negative (-3:00, -4:00, etc.); TDFs for Europe, Africa, Asia and Australia will be positive (1:00, 2:00, etc.). This time zone supports daylight saving time. Is this time zone currently on daylight saving time? (Yes/No): n Enter the Time Differential Factor [-5:00]: NEW SYSTEM TIME DIFFERENTIAL FACTOR = -5:00 Is this correct? [Y]:
The installation operation can provide brief or detailed descriptions. In either case, you can request the detailed descriptions by typing "?". Do you always want detailed descriptions? (Yes/No) [No]
Version 7.3-1 of the OpenVMS operating system is already installed on the target disk. You may choose one of the following actions: o Reconfigure the OpenVMS platform. This action will allow you to change your selections of which of the windowing and network products you included with your OpenVMS operating system installation. o Reconfigure the OpenVMS operating system. This action will allow you to change your choices about which options you included for the OpenVMS operating system. o Reinstall the OpenVMS operating system. This action will cause ALL operating system files to be replaced. You can also change your choices about which options you included for the OpenVMS operating system. Reinstall will take longer than Reconfigure. Reinstall may be appropriate if you suspect that files in the operating system, or in the windowing and network products have become corrupted. If you want to reinstall any of the windowing and network products, choose "Install or upgrade layered products and patches" (option 3) from the main menu. If you want to change your choices about which options you included for any of the windowing and network products, choose "Reconfigure installed products" (option 5) from the main menu. Please choose one of the following: 1) Reconfigure the OpenVMS platform. 2) Reconfigure the OpenVMS operating system. 3) Reinstall the OpenVMS operating system. 4) Return to the Main Menu (abort the upgrade/installation). Enter choice or ? for help: (1/2/3/4/?)
The following product has been selected: DEC AXPVMS OPENVMS V7.3-1 Platform (product suite) Configuration phase starting ... You will be asked to choose options, if any, for each selected product and for any products that may be installed to satisfy software dependency requirements. DEC AXPVMS OPENVMS V7.3-1: OpenVMS and related products platform COPYRIGHT (c) 14-MAY-2002 -- All rights reserved Compaq Information Technologies Group, L.P. Do you want the defaults for all options? [YES] DEC AXPVMS DECNET_PHASE_IV V7.3-1: DECNET_PHASE_IV Support addendum to DECnet Phase IV service contract required Do you want to continue? [YES]
%PMA0 CPU00: 30-MAY-2002 14:58:40 Remote System Conflicts with Known System - REMOTE NODE %PMA0 CPU00: 30-MAY-2002 14:58:45 Remote System Conflicts with Known System - REMOTE NODE
Do you want to review the options? [NO] Execution phase starting ... The following products will be installed to destinations: CPQ AXPVMS CDSA V1.0 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS DECNET_OSI V7.3-1 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS DWMOTIF V1.2-6 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS OPENVMS V7.3-1 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS VMS V7.3-1 DISK$ALPHASYS:[VMS$COMMON.] The following products will be removed from destinations: DEC AXPVMS DECNET_OSI V7.3 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS DWMOTIF V1.2-5 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS OPENVMS V7.3 DISK$ALPHASYS:[VMS$COMMON.] DEC AXPVMS VMS V7.3 DISK$ALPHASYS:[VMS$COMMON.] Portion done: 0%..10%..20%..30%..40%..50%..60%..70%..80%..90%..100% The following products have been installed: CPQ AXPVMS CDSA V1.0 Layered Product DEC AXPVMS DECNET_OSI V7.3-1 Layered Product DEC AXPVMS DWMOTIF V1.2-6 Layered Product DEC AXPVMS OPENVMS V7.3-1 Platform (product suite) DEC AXPVMS VMS V7.3-1 Operating System The following products have been removed: DEC AXPVMS DECNET_OSI V7.3 Layered Product DEC AXPVMS DWMOTIF V1.2-5 Layered Product DEC AXPVMS OPENVMS V7.3 Platform (product suite) DEC AXPVMS VMS V7.3 Operating System The upgrade is now complete. When the newly upgraded system is first booted, a special startup procedure will be run. This procedure will: o Run AUTOGEN to set system parameters. o Reboot the system with the newly set parameters. You may shut down now or continue with other operations. Process AXPVMS_INSTALL logged out at 12-MAY-2002 15:34:22.47 Press Return to continue... **************************************************************** You can install or upgrade the OpenVMS Alpha operating system or you can install or upgrade layered products that are included on the OpenVMS Alpha operating system CD-ROM. You can also execute DCL commands and procedures to perform "standalone" tasks, such as backing up the system disk. Please choose one of the following: 1) Upgrade, install or reconfigure OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system
DEC AXPVMS UCX V4.2-PLACEHOLDER
The UCX implementation of TCP/IP Services is obsolete and is not supported on OpenVMS V7.3-1 and higher versions. Starting with OpenVMS V7.3-1, the UCX implementation of TCP/IP services is replaced by the new TCPIP product. This is a placeholder kit to satisfy OpenVMS upgrade requirements so that UCX can be automatically upgraded to TCPIP. You cannot use this kit to install UCX.
DEC AXPVMS TCPIP V5.1
Please choose one of the following: 1) Upgrade, install or reconfigure OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system Enter CHOICE or ? for help: (1/2/3/4/5/6/7/8/?) 2 The following versions of the OpenVMS operating system, the DECwindows graphical user interface and network products. are available on the OpenVMS Distribution compact disk. They can be installed by selecting choice 1: DEC AXPVMS VMS version V7.3-1 DEC AXPVMS DWMOTIF version V1.2-6 DEC AXPVMS DECNET_OSI version V7.3-1 DEC AXPVMS DECNET_PHASE_IV version V7.3-1 DEC AXPVMS TCPIP version V5.1 The following Layered Product kits are available on the OpenVMS Distribution Compact Disk. They can be installed by selecting choice 3. If already installed, they can be reconfigured by selecting choice 5, or removed by selecting choice 6. ----------------------------------- ----------- ---------- PRODUCT KIT TYPE KIT FORMAT ----------------------------------- ----------- ---------- DEC AXPVMS DECNET_OSI V7.3-1 Full LP Sequential DEC AXPVMS DECNET_PHASE_IV V7.3-1 Full LP Sequential DEC AXPVMS DWMOTIF V1.2-6 Full LP Sequential DEC AXPVMS TCPIP V5.1 Full LP Sequential DEC AXPVMS UCX V4.2-99PLACEHOLDER Full LP Sequential ----------------------------------- ----------- ---------- 5 items found Press Return to continue... **************************************************************** You can install or upgrade the OpenVMS Alpha operating system or you can install or upgrade layered products that are included on the OpenVMS Alpha operating system CD-ROM. You can also execute DCL commands and procedures to perform "standalone" tasks, such as backing up the system disk. Please choose one of the following: 1) Upgrade, install or reconfigure OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system Enter CHOICE or ? for help: (1/2/3/4/5/6/7/8/?) 3 *********************************************************** If you choose to install or upgrade to DECwindows Motif, please note the following: o If you did not select the OpenVMS DECwindows base support and workstation files options, DECwindows Motif will not run. You must add these options to use DECwindows Motif. o If you are upgrading DECwindows Motif from Version 1.1 and want to save the OSF/Motif Release 1.1.3 programming files, DO NOT upgrade now. Instead, see the DECwindows Motif Installation Manual and follow the instructions for running PCSI_INSTALLATION.COM. If you choose to install or upgrade DECnet-Plus or DECnet Phase IV, please note the following: o If you did not select the OpenVMS DECNET option, neither version of DECnet will run. You must add this option to use DECnet. You must enter the device name for the target disk on which the layered product(s) install will be performed. Enter device name for target disk: (? for choices) DKB400 DKB400: is labeled ALPHASYS. The installation can provide brief or detailed descriptions. In either case, you can request the detailed descriptions by typing "?". Do you always want detailed descriptions? (Yes/No) [No] 1 - DEC AXPVMS DECNET_OSI V7.3-1 Layered Product 2 - DEC AXPVMS DECNET_PHASE_IV V7.3-1 Layered Product 3 - DEC AXPVMS DWMOTIF V1.2-6 Layered Product 4 - DEC AXPVMS TCPIP V5.1 Layered Product 5 - DEC AXPVMS UCX V4.2-99PLACEHOLDER Layered Product 6 - All products listed above 7 - Exit Choose one or more items from the menu separated by commas:
IF
... |
THEN
... |
---|---|
you
have one system disk, |
do
the following: 1. Reboot each system that uses the upgraded
disk. |
you
have multiple system disks, |
do
the following: 1. Reboot the upgraded system. 2. Repeat the upgrade process for each system
disk in the cluster, beginning with the preupgrade tasks described in Chapter 5, Before
Upgrading the OpenVMS Alpha Operating System. 3. Reboot each system in the cluster. 4. Log in to an upgraded system. 5. Go to Chapter 8, After Upgrading the OpenVMS
Alpha Operating System to perform additional postupgrade procedures.
|
%AUTOGEN-W-DSKSPC, The disk on which DKA0:[SYS0.SYSEXE]PAGEFILE.SYS resides would be over 95% full if it were modified to hold 20000 blocks.
[SYSMGR]LAT$SYSTARTUP.COM [SYSMGR]LOGIN.COM [SYSMGR]SYCONFIG.COM [SYSMGR]SYLOGICALS.COM [SYSMGR]SYLOGIN.COM [SYSMGR]SYPAGSWPFILES.COM [SYSMGR]SYSECURITY.COM [SYSMGR]SYSHUTDWN.COM [SYSMGR]SYSTARTUP_VMS.COM [SYSMGR]TFF$SYSTARTUP.COM [SYSMGR]WELCOME.TXT [SYS$STARTUP]ESS$LAST_STARTUP.DAT
$ @SYS$STARTUP:CDSA$INITIALIZE
Do you want to review the options? [NO] Execution phase starting ... The following product will be reconfigured: DEC AXPVMS VMS V7.3-1 Portion done: 0%..10%..20%..30%..40%..50%..60%..70%..80%..90%..100% The following product has been reconfigured: DEC AXPVMS VMS V7.3-1 . . .
CPU |
Operating
System |
Client
Kit |
---|---|---|
Alpha |
Windows
NT |
40COMAXP.EXE |
Intel |
Windows
NT |
40COMUPD.EXE |
Alpha |
Windows
NT |
DEBUGALPHA011.EXE |
Intel |
Windows
95, 98, Me, NT, 2000, XP |
DEBUGX86011.EXE |
Install
Option |
Details |
---|---|
Typical |
Debug
Client and theOpenVMS Debugger Manual in
HTML format |
Compact |
Debug
Client only |
Custom |
Choice
of Debug Client and/or the OpenVMS Debugger
Manual in HTML format |
System
Parameter |
Default
Value |
---|---|
NPAG_BAP_MIN |
0 |
NPAG_BAP_MAX |
0 |
NPAG_BAP_MIN_PA |
0 |
NPAG_BAP_MAX_PA |
-1 |
$ @SYS$UPDATE:AUTOGEN SAVPARAMS SETPARAMS FEEDBACK
$ @SYS$SYSTEM:AGEN$FEEDBACK.EXE
$ SEARCH SYS$SYSTEM:AGEN$FEEDBACK.DAT "BAP_"
AGEN$FEEDBACK Data |
System Parameter |
Units |
---|---|---|
BAP_MIN |
NPAG_BAP_MIN |
bytes |
BAP_MAX |
NPAG_BAP_MAX |
bytes |
BAP_MIN_PA |
NPAG_BAP_MIN_PA |
Mbyte1
(SEE NOTE) |
BAP_MAX_PA |
NPAG_BAP_MAX_PA |
Mbytes1 |
Alpha Computer |
Ethernet Device |
FDDI Device |
---|---|---|
ALPHAbook
1 |
EOA0 |
— |
AlphaServer
400 series |
EWA0 |
FWA0 |
AlphaServer
1000 series |
ERA0,
EWA0 |
FRA0 |
AlphaServer
1000A series |
EWA0 |
FWA0 |
AlphaServer
1200 series |
EWA0 |
FWA0 |
AlphaServer
2000 series |
ERA0,
EWA0 |
FRA0 |
AlphaServer
2100, 2100A series |
ERA0,
EWA0 |
FRA0 |
AlphaServer
4100 series |
EWA0 |
FWA0 |
AlphaServer
8200 series |
EXA0,
EWA0 |
FXA0 |
AlphaServer
8400 series |
EXA0,
EWA0 |
FXA0 |
AlphaStation
200 series |
EWA0 |
FWA0 |
AlphaStation
400 series |
EWA0 |
FWA0 |
AlphaStation
500 series |
EWA0 |
FWA0 |
AlphaStation
600 series |
ERA0,
EWA0 |
FWA0 |
DEC
2000 series |
ERA0 |
— |
DEC
3000 series |
ESA0 |
"n/ESA0" |
DEC
4000 series |
EZA0 |
— |
DEC
7000 series |
EXA0 |
FXA0 |
DEC
10000 series |
EXA0 |
FXA0 |
Digital
Personal Workstation (DPWS) series |
EWA0 |
FWA0 |
Network Initial System Load Function Version 1.2 FUNCTION FUNCTION ID 1 - Display Menu 2 - Help 3 - Choose Service 4 - Select Options 5 - Stop Enter a function ID value:
IF
... |
THEN
... |
---|---|
the
OpenVMS Alpha operating system is running, |
go
to step 1. |
the
OpenVMS Alpha operating system is not running, |
go
to step 4. |
SYSTEM SHUTDOWN COMPLETE
IF
... |
THEN
... |
---|---|
the
OpenVMS Alpha operating system is running, |
go
to step 1. |
the
OpenVMS Alpha operating system is not running, |
go
to step 4. |
SYSTEM SHUTDOWN COMPLETE
Command |
Description |
---|---|
CONTINUE |
Resumes
the boot procedure. |
DISABLE
CHECKS |
Inhibits
checking of parameter values specified with the SET command. |
ENABLE
CHECKS |
Permits
checking of parameter values specified with the SET command. |
HELP |
Displays
a summary of the SYSBOOT commands on the terminal screen. |
SET parameter-name |
Establishes
the value of a system parameter. |
SET/STARTUP |
Sets
the name of the system startup command procedure. |
SHOW
[parameter] |
Displays
active, current, default, maximum, and minimum values for specific parameters.
(Use qualifiers to display characteristics of parameters grouped by categories.) |
USE
[file-spec] |
Specifies
a parameter file to be used as a source of values. You must enter the entire
file specification, including device and directory; you cannot specify a
logical name. |
Value |
System
Response |
---|---|
0 |
Normal,
nonstop boot (default). |
1 |
Begins
a conversational boot and then displays the SYSBOOT prompt. |
2 |
Includes
XDELTA but does not take the initial breakpoint. |
3 |
Displays
the SYSBOOT prompt and includes XDELTA but does not take the initial breakpoint. |
6 |
Includes
XDELTA and takes the initial breakpoint. |
7 |
Includes
XDELTA, displays the SYSBOOT prompt, and takes the initial breakpoint at system
initialization. |
Operation |
When
to Use |
---|---|
Booting
with default system parameters |
When
parameter values in the parameter file have been modified so that the system
is unbootable |
Booting
without startup and login procedures |
If
an error in the startup or login procedures prevents you from logging in |
Booting
without the user authorization file |
If
you have forgotten the password and cannot log in to a privileged account |
. . .
. . .
Field |
Value |
---|---|
Name |
User
name |
UIC |
[001,004] |
Command
interpreter |
DCL |
Login
flags |
None |
Priority |
Value
of the system parameter, DEFPRI |
Resources |
Values
of the PQL system parameters |
Privileges |
All |
IF
... |
THEN
... |
---|---|
the
OpenVMS Alpha operating system is running, |
go
to step 1. |
the
OpenVMS Alpha operating system is not running, |
go
to step 4. |
SYSTEM SHUTDOWN COMPLETE
Hexadecimal
Value |
System
Response |
---|---|
1 |
Allows
a conversational boot (the system displays the SYSBOOT> prompt). |
2 |
Maps
XDELTA to a running system. |
4 |
Stops
the boot procedure at the initial system breakpoint. |
8 |
Performs
a diagnostic bootstrap. |
10 |
Stops
the boot procedure at the bootstrap breakpoints. |
20 |
Omits
header from secondary bootstrap image. |
80 |
Prompts
for the name of the secondary bootstrap file. |
100 |
Halts
the system before the secondary bootstrap. |
2000 |
Marks
corrected read data error pages as bad. |
10000 |
Displays
extensive, detailed debug messages during the boot process. |
20000 |
Displays
selected user-oriented messages during the boot process. |
Update VAX portion of boot block (default is Y): Update Alpha portion of boot block (default is Y):
Enter Alpha boot file:
Alpha
Computer |
How
to Halt |
---|---|
AlphaServer
300, 800, 1000, 1200, 2000, 2100 series |
Do
one of the following: • Press the Halt button. • Press Ctrl/P. |
AlphaServer
8200, 8400 series |
Press
Ctrl/P. |
AlphaStation
200, 400, 500, 600 series |
Do
one of the following: • Press the Halt button (if the graphics
monitor is serving as the console). • Press Ctrl/P (if you are using the
alternate console and port). |
DEC
2000, 3000 series |
Do
one of the following: • Press the Halt button (if the graphics
monitor is serving as the console). • Press Ctrl/P (if you are using the
alternate console and port). |
DEC
4000 series |
Do
one of the following: • Press the Halt button. • Press the Break key on the console
(the default setting). • Press Ctrl/P, but only after using
the console command SET TTA0_HALTSn to
enable this key combination, where n can
be 6 (enables the Break key and Ctrl/P) or 2 (enables Ctrl/P but disables
the Break key). |
DEC
7000, 10000 series |
Press
Ctrl/P. |
SYSTEM job terminated at 27-MAY-2002 15:05:03.17
**************************************************************** You can install or upgrade the OpenVMS Alpha operating system or you can install or upgrade layered products that are included on the OpenVMS Alpha operating system CD-ROM. You can also execute DCL commands and procedures to perform "standalone" tasks, such as backing up the system disk. Please choose one of the following: 1) Upgrade, install or reconfigure OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system Enter CHOICE or ? for help: (1/2/3/4/5/6/7/8/?) 7
You can install or upgrade the OpenVMS Alpha operating system or you can install or upgrade layered products that are included on the OpenVMS Alpha operating system CD-ROM. You can also execute DCL commands and procedures to perform "standalone" tasks, such as backing up the system disk. Please choose one of the following: 1) Upgrade, install or reconfigure OpenVMS Alpha Version 7.3-1 2) Display products and patches that this procedure can install 3) Install or upgrade layered products and patches 4) Show installed products 5) Reconfigure installed products 6) Remove installed products 7) Execute DCL commands and procedures 8) Shut down this system Enter CHOICE or ? for help: (1/2/3/4/5/6/7/8/?) 7
DEC AXPVMS OPENVMS V7.3-1: OpenVMS and related products platform COPYRIGHT (c) 14-MAY-2002 -- All rights reserved Compaq Information Technologies Group, L.P. Execution phase starting ... The following product will be installed: DEC AXPVMS VMS V7.3-1 Portion Done: 0%..10%..20%..30%..40%..50%..60%..70%..80%..90%..100% The following product has been installed: DEC AXPVMS VMS V7.3-1 . . . The installation of minimum OpenVMS Alpha is now complete. Use the following command to boot minimum OpenVMS: BOOT -FLAGS E,O device-name (Your system may require additional parameters to boot.)
%LICENSE-I-NOLICENSE, no license is active for this software product
http://www.compaq.com/products/software/info/refmat/swl_alpha.HTML
%LICENSE-F-EXCEEDED, licensed product has exceeded current license limits
http://www.openvms.compaq.com/openvms/products/argus/index.HTML#ordering
Command |
Parameter
1 |
Parameter
2 |
Description |
---|---|---|---|
@TNT$STARTUP |
blank |
N.A. |
Starts
the server. Does not start printer queues or mount volumes. |
@TNT$STARTUP |
RESTART |
N.A. |
Shuts
down a running server, then starts the server. Does not start printer queues
or mount volumes. |
@TNT$STARTUP |
BOOT |
blank |
Starts
the server. Starts any printer queues that are not yet started and are managed
by OpenVMS Management Station. Does not mount volumes managed by OpenVMS Management
Station. |
@TNT$STARTUP |
BOOT |
ALL |
Starts
the server. Starts any printer queues that are not yet started and are managed
by OpenVMS Management Station. Mounts any volumes that are not yet mounted
and are managed by OpenVMS Management Station. |
@TNT$STARTUP |
BOOT |
PRINTERS |
Starts
the server. Starts any printer queues that are not yet started and are managed
by OpenVMS Management Station. Does not mount volumes managed by OpenVMS
Management Station. |
@TNT$STARTUP |
BOOT |
STORAGE |
Starts
the server. Mounts any volumes that are not yet mounted and are managed by
OpenVMS Management Station. Does not start any printer queues. |
Logical Name |
Description |
---|---|
TNT$PRINTER_RECON_ INTERVAL |
How
often the thread should run, in minutes, from when the server was last started
on this node. If you do not define this logical, the default value is 1440
minutes (24 hours). |
TNT$PRINTER_RECON_ INTERVAL_MIN |
The
minimum number of minutes that must elapse before the thread should run again,
starting from when the database was last updated. If you do not define this
logical, the default value is 60 minutes (1 hour). |
min = 180 default = 1800 (30 minutes) max = 18000 (5 hours)
min = 6 default = 60 (1 minute) max = 600 (10 minutes)
privacy and legal statement | ||
6655PRO.HTML |