日本語 Compaq Advanced Server for OpenVMS
インストレーションおよび構成ガイド


前へ 次へ 目次 索引



付録 A
インストレーションおよびアップグレードのチェックリスト

表 A-1 に, Advanced Server をインストールおよび構成するために行う必要があるタスクを要約します。本書でタスクについて読み,それを行うときには,この表をコピーしてチェックリストとして使用することができます。

表 A-1 インストレーションおよびアップグレードのチェックリスト
[   ] 1. 第 1.8 節, インストレーション前の手順 」のチェックリストにある,次のようなインストレーション前のタスクを行うことにより,インストレーションの準備を整える。
  1. パーツ一覧を確認する。
  2. 必要なハードウェアが揃っていることを確認する。
  3. SYSTEMアカウント(または同等のアカウント)にログインする。
  4. システムに必要なソフトウェアがインストールされていることを確認する。
  5. Advanced Serverシステムで,OpenVMSレジストリ・サービスが利用可能であることを確認する。
  6. リリース・ノートを読む。
  7. GBLPAGES,GBLSECTIONS, PROCSECTCNT,およびSCSNODEというシステム・パラメータが正しく設定されていることを確認する。
  8. システム・ディスクをバックアップする。
  9. このソフトウェアをインストールするために必要なディスク領域があることを確認する。
  10. キュー・マネージャが実行されていることを確認する。
  11. タイム・ゾーン構成を確認する。
  12. 必要に応じて,DECnet (またはDECnet-Plus)およびTCP/IPが稼動していることを確認する。
  13. システムに既存のCompaq OpenVMS サーバ・イメージおよびファイルがあるかどうかを確認する。
  14. クラスタ上にインストールする場合は,OpenVMS Cluster構成を確認する。

[   ] 2. インストレーション・プロシージャを起動し,インストレーション・プロンプトに答える。次のものがインストールできる。
  • 完全な Advanced Server
  • スタンドアロン License Server ( Advanced Server のインストレーションを選択しない場合)
  • スタンドアロン外部認証ソフトウェア( Advanced Server のインストレーションを選択しない場合)
  • スタンドアロン License Serverと外部認証ソフトウェアの両方 ( Advanced Server のインストレーションを選択しない場合)

[   ] 3. 構成プロシージャを起動し,構成プロンプトに答える。
[   ] 4. インストレーション検証プロシージャを実行する ( Advanced Server のインストレーション時に行わなかった場合)。
[   ] 5. サーバを起動する ( Advanced Server のインストレーション時に起動しなかった場合)。
[   ] 6. Windows NTサーバ管理ツールをインストールする(オプション)。


付録 B
Advanced Server のインストレーションおよび構成の例

この付録では, Advanced Server がシステムに初めてインストールされる場合のインストレーションおよび構成プロシージャの例を示します。

B.1 Advanced Server のインストレーション・プロシージャの例

次に, Advanced Server のインストレーション・ダイアログの例を示します。システムの環境により,インストレーション・ダイアログが少し異なります。


$ PRODUCT INSTALL ADVANCEDSERVERJA/SOURCE=DKA100:[000000] 
 
The following product has been selected: 
    CPQ AXPVMS ADVANCEDSERVERJA V7.3         Layered Product 
 
 
Configuration phase starting ... 
 
You will be asked to choose options, if any, for each selected product 
and for 
any products that may be installed to satisfy software dependency 
requirements. 
 
CPQ AXPVMS ADVANCEDSERVERJA V7.3: Advanced Server for OpenVMS 
 
    Copyright 2000 Compaq Computer Corporation 
 
    Advanced Server is sold by Compaq Computer Corporation 
 
    Advanced Server requires PAK PWLMXXXCA07.03 for each client. 
    
        This installation procedure requires that all the following 
        conditions are satisfied: 
        1.  This procedure is running on an Alpha processor. 
        2.  The system is running OpenVMS 7.2 or later. 
        3.  All required privileges are currently enabled. 
        4.  No PATHWORKS or Advanced Server images are running 
            on this node or anywhere in the cluster. 
        5.  No files from a PATHWORKS (NetWare) kit are present 
            on this system disk. 
        6.  No files from any Pathworks or Advanced Server kit 
            are in SYS$SPECIFIC on this system disk. 
 
        This procedure checks if the conditions are satisfied. 
        If they are satisfied, the procedure continues. If not, 
        the procedure stops. 
 
Do you want to continue? [YES] [Return]
 
        Select one of the numbered options: 
        1  Install the complete Advanced Server         [default] 
        2  Install only the License Server 
        3  Install only the external authentication images 
        4  Install both the License Server and the 
                external authentication images 
Option: [1] [Return]
 
This node contains a PWRK$STREAMSOS_V*.EXE execlet from a previous kit 
loaded into memory. 
A node that will not run this product does not have to be rebooted. 
A node that did not run a previous version of this product does not 
have to be rebooted.  Only nodes that ran a previous version and 
will run the new version must be rebooted. 
 
Depending on the existing configuration and the desired configuration 
of a node it might be necessary to reboot a node before it can be 
configured, after it has been configured, or both. Both is rare. 
 
For complete information about the reasons a reboot might be 
necessary and how to avoid unnecessary reboots, see the Installation 
and Configuration Guide. 
 
Select an option: 
1. Delay reboot as long as possible on all nodes. [default] 
2. Prevent PWRK$CONFIG configuration on any node using this system 
   disk until after reboot. 
3. Prevent PWRK$CONFIG configuration on all nodes until after reboot. 
4. Prevent startup on any node using this system disk until after 
   reboot. 
5. Prevent startup on all nodes until after reboot. 
 
Option: [1] [Return]
 
              User Accounts and User Identification Codes (UICs) 
              -------------------------------------------------- 
 
    The Advanced Server V7.3 for OpenVMS installation creates two 
    OpenVMS accounts:  a default account, PWRK$DEFAULT, and a guest 
    account, PWRK$GUEST.  The default UIC group number for both 
    these new accounts depends on the following: 
 
     o If you are installing the server for the first time, the 
       default is the first unused UIC group number, starting 
       with 360. 
 
     o If a PCFS$ACCOUNT already exists, the default is 
       the UIC group number associated with PCFS$ACCOUNT. 
 
     o If a PWRK$DEFAULT or PWRK$GUEST account already exists, 
       the default is the UIC group number associated with 
       PWRK$DEFAULT or PWRK$GUEST, in preference to PCFS$ACCOUNT. 
       However, the default UIC group number will not be used to 
       change the UIC of any existing accounts. 
 
     For more information about UIC group numbers, see the 
     OpenVMS System Manager's Manual. 
 
Enter default UIC group number for 
PWRK$DEFAULT and PWRK$GUEST 
Group: [360] [Return]
Creating OpenVMS accounts for PWRK$DEFAULT and PWRK$GUEST 
PWRK$DEFAULT account already exists 
PWRK$GUEST account already exists 
 
* This product does not have any configuration options. 
 
Execution phase starting ... 
 
The following product will be installed to destination: 
    CPQ AXPVMS ADVANCEDSERVERJA V7.3         DISK$AXP0721:[VMS$COMMON.] 
 
Portion done: 0%...10%...20%...30%...40%...60%...90% 
    To automatically start Advanced Server V7.3 for OpenVMS at 
    system startup, you should add the following line to the 
    SYS$MANAGER:SYSTARTUP_VMS.COM file. 
 
        $ @SYS$STARTUP:PWRK$STARTUP 
 
    Note: Add this line after the lines that start all the network 
    transports, such as DECnet. 
 
    Before starting Advanced Server V7.3 for OpenVMS on this node, 
    be sure to configure the product (@SYS$UPDATE:PWRK$CONFIG) on 
    each node in the cluster where the product will run. 
...100% 
 
The following product has been installed: 
    CPQ AXPVMS ADVANCEDSERVERJA V7.3         Layered Product 
 
%PCSI-I-IVPEXECUTE, executing test procedure for CPQ AXPVMS 
 ADVANCEDSERVERJA V7.3 ... 
 
Copyright Compaq Computer Corporation 1998, 2000. 
 
        Starting Installation Verification Procedure 
        for Advanced Server V7.3 for OpenVMS 
 
%PWRK-I-NORMAL, IVP completed successfully 
%PCSI-I-IVPSUCCESS, test procedure completed successfully 
$ 
 

B.2 Advanced Server 構成プロシージャの例

次に, Advanced Server の構成ダイアログの例を示します。


$ @SYS$UPDATE:PWRK$CONFIG 
Advanced Server V7.3 for OpenVMS Configuration Procedure 
 
  The Advanced Server stores and accesses the following 
  types of data files: 
 
  o Configuration parameter files 
  o License Server data files 
  o Log files 
  o Printer spool files 
  o Virtual memory section files 
 
  You can specify any existing OpenVMS disk device that has at least 
  85,000 free blocks of disk space to store these data files. 
 
  Note: The server frequently accesses the data files stored on the 
  disk.  If these files are stored on the system disk, it can degrade 
  the performance of both the OpenVMS system and the server.  Therefore, 
  Compaq recommends that you specify a disk other than the system disk. 
 
Press RETURN to continue: 
 
  If this OpenVMS cluster has multiple system disks, make sure that all 
  nodes on which you plan to run the Advanced Server: 
 
  o Use the same disk device to store and access Advanced Server 
    data files. 
 
  o Share the same SYSUAF.DAT file. In each system disk's startup file, 
    define a system logical name that points all nodes to the shared 
    SYSUAF.DAT file. For example: 
 
    $ define/system/exec sysuaf pencil$dka300:[sys0.sysexe]sysuaf.dat 
 
    The startup file is called SYS$MANAGER:SYSTARTUP_VMS.COM 
 
Enter disk device name where the Advanced Server data files will be 
stored [SYS$SYSDEVICE:]: [Return]
Creating Advanced Server directory tree on PWROOT:... 
PWRK$LICENSE_SERVER_STATE.DAT already exists, not superseded. 
%CREATE-I-EXISTS, PWRK$COMMONROOT:[000000] already exists 
Checking to see if the OpenVMS Registry Services are available... 
%RUN-S-PROC_ID, identification of created process is 0000023B 
Populating OpenVMS Registry with required Advanced Server & NT 
parameters... 
Please wait, this may take one to two minutes to complete ... 
Required OpenVMS Registry file server keys and values have been created. 
Migrating LANMAN.INI parameters to the OpenVMS Registry... 
Verifying SAM database files... 
Creating Advanced Server directory tree... 
Copying client files to Advanced Server directory tree... 
Creating the Monitor user authorization file PWRK$COMMON:PWMONUAF.DAT... 
 
  Changing the server configuration parameters will allow you to modify 
  this server's client capacity and select the transports to be used.  
 
  SPEEDY is currently configured to 
      + support 20 PC clients 
      + use the following transport(s): DECnet 
 
  If you want this server to be the primary domain controller, you 
  should configure it to use all the transports used by the backup 
  domain controllers and member servers in the domain. 
 
  If you want this server to be a backup domain controller or 
  member server, you should configure it to have at least one 
  transport in common with the domain's primary domain controller, 
  otherwise this configuration will fail. 
 
  If you do not change the configuration parameters now, you may do 
  so later by typing ADMIN/CONFIG. 
 
Do you want to change the server configuration parameters now? 
[YES]:Y [Return]
 
******* Advanced Server Configuration for node SPEEDY ********* 
* Options Help                                                * 
*                                                             * 
*                                                             * 
* *Server's Client Capacity********************************** * 
* *                                                         * * 
* *                                                         * * 
* * (  ) Maximize Client Capacity Using AUTOGEN/Reboot      * * 
* * (* ) Maximize Client Capacity Without AUTOGEN or Reboot * * 
* * (  ) User Supplied Client Capacity                      * * 
* *                                                         * * 
* *  Client Capacity: 20                                    * * 
* *                                                         * * 
* *********************************************************** * 
*                                                             * 
* Percent of Physical Memory Used: 80                         * 
*                                                             * 
* Data Cache Size (Kbytes): 12888                             * 
*                                                             * 
* Maximum Concurrent Signons: 10                              * 
* OpenVMS Process Priority: 9                                 * 
*                                                             * 
* **********  ********  ***************  *****************    * 
* * Verify *  * Quit *  * Advanced... *  * Transports... *    * 
* **********  ********  ***************  *****************    * 
*                                                             * 
* Enter data cache size in Kbytes ***************************** 
   .
   .
   .
Reading current configuration parameters ... 
 
  Your Advanced Server for OpenVMS is presently configured to 
  run as follows: 
 
   1.  Run the License Server:          NO 
   2.  Enable Timesource service:       NO 
   3.  Enable Alerter service:          YES 
   3a. Alert user names:                Administrator 
   4.  Enable Netlogon service:         YES 
   5.  Advanced Server domain:          LANGROUP 
   6.  Advanced Server role:            PRIMARY 
   7.  Advanced Server computer name:   SPEEDY 
   7a. Advanced Server OpenVMS Cluster alias:   SPEEDY_ALIAS 
   8.  Server announce comment:    Advanced Server V7.3 for OpenVMS 
   9.  Advanced Server language:        English (USA) 
  10.  Enable NT style printing:        NO 
Enter item number, or RETURN to use these values [DONE]: 5 [Return]
 
  An Advanced Server domain is a collection of computers that share 
  a common security database and policy.  Each domain has a unique 
  name.  A network can have many domains. 
 
  The Advanced Server domain name can be up to 15 characters long. 
  The domain name must be different than the computer name. 
 
Enter Advanced Server domain name for this system [5]: SPUNKY.DOM 
[Return]
 
  Your Advanced Server for OpenVMS is presently configured to 
  run as follows: 
 
   1.  Run the License Server:          NO 
   2.  Enable Timesource service:       NO 
   3.  Enable Alerter service:          YES 
   3a. Alert user names:                Administrator 
   4.  Enable Netlogon service:         YES 
   5.  Advanced Server domain:          SPUNKY.DOM 
   6.  Advanced Server role:            PRIMARY 
   7.  Advanced Server computer name:   SPEEDY 
   7a. Advanced Server OpenVMS Cluster alias:   SPEEDY_ALIAS 
   8.  Server announce comment:    Advanced Server V7.3 for OpenVMS 
   9.  Advanced Server language:        English (USA) 
  10.  Enable NT style printing:        NO 
Enter item number, or RETURN to use these values [DONE]: [Return]
 
Saving parameters to the OpenVMS Registry... 
Creating SAM datafiles... 
Creating sharefile PWRK$LMROOT:[LANMAN.DATAFILES]SHAREDB ... 
New sharefile has been created. 
ADMIN$ added 
IPC$ added 
PWUTIL added 
PWLICENSE added 
PWLIC added 
 
    The Advanced Server Administrator account is used to 
    administer the server.  The Administrator account 
    is mapped by default to the OpenVMS SYSTEM account. 
 
    The account password can be up to 14 characters long 
    and the case of the characters used will be preserved. 
 
Enter Administrator account password: 
Re-enter to verify password: 
 
Changing password for Administrator account... 
Checking system resources... 
 
The current system configuration for SPEEDY will support 20 PC 
clients. 
The Advanced Server is configured to use DECnet, NetBEUI, TCP/IP. 
 
    To automatically start the Advanced Server V7.3 for OpenVMS 
    at system startup, you should add the following line to the 
    SYS$MANAGER:SYSTARTUP_VMS.COM file. 
 
      $ @SYS$STARTUP:PWRK$STARTUP 
 
    Note: Add this line below the lines that start all network 
    transports (such as DECnet). 
 
Do you want to start the Advanced Server V7.3 on node SPEEDY now 
[YES]: [Return]
The file server will use DECnet, NetBEUI, TCP/IP. 
Advanced Server mail notification will use DECnet. 
Process NETBIOS created with identification 00000248 
Process PWRK$NBDAEMON created with identification 0000024A 
Process PWRK$KNBDAEMON created with identification 0000024C 
Process PWRK$LICENSE_R created with identification 0000024E 
Checking to see if the OpenVMS Registry Services are available... 
The Advanced Server is configured to support 20 PC clients. 
Process PWRK$MASTER created with identification 00000251 
The master process will now start all other Advanced 
Server processes. 
 
$               


付録 C
スタンドアロンLicense Serverのインストレーションと構成の例

この付録では,OpenVMS ClusterにおけるスタンドアロンLicense Server のインストレーションおよび構成プロシージャの例を示します。

C.1 スタンドアロンLicense Serverのインストレーション・プロシージャの例

次に,スタンドアロンLicense Serverのインストレーション・ダイアログの例を示します。


$ PRODUCT INSTALL ADVANCEDSERVERJA [RETURN]
 
The following product has been selected: 
    CPQ AXPVMS ADVANCEDSERVERJA V7.3         Layered Product 
 
Do you want to continue? [YES] [RETURN]
 
Configuration phase starting ... 
 
You will be asked to choose options, if any, for each selected product 
and for 
any products that may be installed to satisfy software dependency 
requirements. 
 
CPQ AXPVMS ADVANCEDSERVERJA V7.3: Advanced Server for OpenVMS 
 
    Copyright 2000 Compaq Computer Corporation 
 
    Advanced Server is sold by Compaq Computer Corporation 
 
    Advanced Server requires PAK PWLMXXXCA07.03 for each client. 
 This installation procedure requires that all the following 
 conditions are satisfied: 
 1.  This procedure is running on an Alpha processor. 
 2.  The system is running OpenVMS 7.2 or later. 
 3.  All required privileges are currently enabled. 
 4.  No PATHWORKS or Advanced Server images are running 
     on this node or anywhere in the cluster. 
 5.  No files from a PATHWORKS (NetWare) kit are present 
     on this system disk. 
 6.  No files from any PATHWORKS or Advanced Server kit 
     are in SYS$SPECIFIC on this system disk. 
 
 This procedure checks if the conditions are satisfied. 
 If they are satisfied, the procedure continues. 
 If not, the procedure stops. 
 
Do you want to continue? [YES] [RETURN]
 Select one of the numbered options: 
 1.  Install the complete Advanced Server         [default] 
 2.  Install only the License Server 
 3.  Install only the external authentication images 
 4.  Install both the License Server and the 
  external authentication images 
Option: [1] 2 [RETURN]
This node does not have to be rebooted before starting this product. 
 
For complete information about the reasons a reboot might be 
necessary and how to avoid unnecessary reboots, see the Installation 
and Configuration Guide. 
 
Select an option: 
1. Delay reboot as long as possible on all nodes. [default] 
2. Prevent PWRK$CONFIG configuration on any node using this system 
   disk until after reboot. 
3. Prevent PWRK$CONFIG configuration on all nodes until after reboot. 
4. Prevent startup on any node using this system disk until 
   after reboot. 
5. Prevent startup on all nodes until after reboot. 
 
Option: [1] 1 [RETURN]
 
* This product does not have any configuration options. 
 
Execution phase starting ... 
 
The following product will be installed to destination: 
    CPQ AXPVMS ADVANCEDSERVERJA V7.3         DISK$AXP0721:[VMS$COMMON.] 
 
Portion done: 0%...10%...20%...30%...40%...50%...60%...70%...80%...90% 
...100% 
 
The following product has been installed: 
    CPQ AXPVMS ADVANCEDSERVERJA V7.3         Layered Product 
 
%PCSI-I-IVPEXECUTE, executing test procedure for CPQ AXPVMS 
 ADVANCEDSERVERJA V7.3 ... 
 
Copyright Compaq Computer Corporation 1998, 2000. 
 
 Starting Installation Verification Procedure 
 for Advanced Server V7.3 for OpenVMS 
 
%PWRK-I-NORMAL, IVP completed successfully 
%PCSI-I-IVPSUCCESS, test procedure completed successfully 

C.2 スタンドアロンLicense Serverの構成ダイアログの例

次に,スタンドアロンLicense Serverの構成ダイアログの例を示します。


$ @SYS$UPDATE:PWRK$CONFIG 
Advanced Server V7.3 for OpenVMS Configuration Procedure 
 
  The Advanced Server stores and accesses the following 
  types of data files: 
 
  o Configuration parameter files 
  o License Server data files 
  o Log files 
  o Printer spool files 
  o Virtual memory section files 
 
  You can specify any existing OpenVMS disk device that has at least 
  5000 free blocks of disk space to store these data files. 
 
  Note: The server frequently accesses the data files stored on the 
  disk.  If these files are stored on the system disk, it can degrade 
  the performance of both the OpenVMS system and the server.  Therefore, 
  Compaq recommends that you specify a disk other than the system disk. 
 
Press RETURN to continue: [Return]
 
  If this OpenVMS Cluster has multiple system disks, make sure that all 
  nodes on which you plan to run the Advanced Server: 
 
  o Use the same disk device to store and access Advanced Server 
    data files. 
 
  o Share the same SYSUAF.DAT file. In each system disk's startup file, 
    define a system logical name that points all nodes to the shared 
    SYSUAF.DAT file. For example: 
 
    $ define/system/exec sysuaf pencil$dka300:[sys0.sysexe]sysuaf.dat 
 
    The startup file is called SYS$MANAGER:SYSTARTUP_VMS.COM 
 
Enter disk device name where the Advanced Server data files will be 
stored [SYS$SYSDEVICE:]: [RETURN]
Creating Advanced Server directory tree on SYS$SYSDEVICE:... 
%CREATE-I-EXISTS, PWRK$COMMONROOT:[000000] already exists 
 
  The License Server can serve client-based licenses for 
  Advanced Server clients over DECnet, NetBEUI, and TCP/IP. 
  The Advanced Server need not be running for the License 
  Server to operate. 
 
Do you want to serve client-based licenses over DECnet [YES]: [Return]
Do you want to serve client-based licenses over NetBEUI [NO]: Y [Return]
Do you want to serve client-based licenses over TCP/IP [NO]: Y [Return]
 
Do you want to start the Advanced Server License Server now [YES]: [Return]
 
The License Server will use DECnet, NetBEUI, TCP/IP. 
 
Process NETBIOS created with identification 2960012B 
 
Process PWRK$NBDAEMON created with identification 2960012D 
 
Process PWRK$KNBDAEMON created with identification 2960012F 
 
Process PWRK$LICENSE_S created with identification 29600131 
 
 To automatically start the License Server at system startup, you 
 should add the following line to the 
 SYS$MANAGER:SYSTARTUP_VMS.COM file: 
 
      $ @SYS$STARTUP:PWRK$LICENSE_STARTUP 
 
  Note: Add this line below the lines that start all network 
  transports (such as DECnet). 
 
$ 


前へ 次へ 目次 索引