Document revision date: 30 March 2001

If your computer does not use console media, skip this section and go to Section 8.10.

If your computer uses console media, you must copy the Version 7.3 VMB.EXE onto your system's console media. The procedure differs depending on the VAX series computer you have. Follow the instructions in the section that applies to your VAX computer.

8.9 VAX 8530, 8550, 8810 (8700), 8820-N (8800) Computers

If you upgraded a VAX 8530, 8550, 8810 (8700), or 8820-N (8800) computer, do the following:

1. Insert a blank RX50 diskette in one of the console diskette drives. The console refers to the upper (or left-hand) diskette drive as DZ1 while the OpenVMS VAX operating system refers to it as CSA1. The console refers to the lower (or right-hand) drive as DZ2 while the OpenVMS VAX operating system refers to it as CSA2.
2. Make sure the diskette drives are connected to the OpenVMS VAX operating system, as follows:

   $ SHOW DEVICE CSA Device Device Error Volume Name Status Count Label CSA0: (SYSTEM) Online 0 CSA1: (SYSTEM) Online 0 CSA2: (SYSTEM) Online 0

   
   If the drives are not connected, the following message is displayed:

   %SYSTEM-W-NOSUCHDEV, no such device available

   
   If this message is displayed, enter the following commands (you need CMKRNL privilege):

   $ RUN SYS$SYSTEM:SYSGEN SYSGEN> CONNECT CONSOLE SYSGEN> EXIT

3. To initialize the disk, enter a command in the following format:

   $ INITIALIZE/STRUCTURE=1 device-name: volume-label

   
   Substitute CSA1 or CSA2 for device-name. Substitute a 1- to 12-character name for volume-label. For example:

   $ INITIALIZE/STRUCTURE=1 CSA1: V61CONSOLE

4. Enter the following commands to mount the diskette, create the required directories, and copy the new VMB.EXE to the diskette. Substitute CSA1 or CSA2 for device-name.

   $ MOUNT/OVERRIDE=ID device-name: $ CREATE/DIRECTORY device-name:[TRANSFER] $ COPY SYS$SYSTEM:VMB.EXE device-name:[TRANSFER]

5. Once you have copied all the files, enter the following command to dismount the diskette. (Leave the diskette in the drive.) Substitute CSA1 or CSA2 for device-name.

   $ DISMOUNT device-name:

6. To enter console mode, press Ctrl/P. To exit the console program, enter the following command:

   >>> EXIT

7. Open the diskette drive door, pause for a moment, and close it. The red indicator light will flash.
8. To copy VMB.EXE from the diskette to the console fixed disk drive, enter the following command:

   $ COPY DZu:[TRANSFER]VMB.EXE LB0:[CONSOLE]

   
   Substitute DZ1 or DZ2 for DZu.
   The fixed drive in the console is known by two names, DW2 and LB0. Most console files are stored using the name LB0. If the system displays a message that describes a protection violation on the output device, copy the files using the device name DW2 rather than LB0.

9. When you have finished copying the files, remove the diskette from the drive.
10. Restart the console program by entering the following command and pressing Return:

    $ RUN CONTROL

11. Return to the operating system by entering the following command and pressing Return:

    >>> SET TERMINAL PROGRAM

If you upgraded a VAX--11/730, 750, 780, 785 and VAX 8200, 8250, 8300, 8350, 8600, or 8650 computer, follow the instructions in this section.

The procedure does the following:

• Checks to see if you have enough space for the new VMB.EXE
• Copies the new VMB.EXE to the console media
• Updates the BOOT58 file for the VAX--11/750, 8200, 8250, 8300, and 8350 computers

To update the console media, use the following procedure:

1. Log in to the SYSTEM account.
2. Enter the following commands to check if there is enough space for the new VMB.EXE. You need 120 blocks. If you are updating a VAX--11/730 system, use CSA2 for device-name; if you are updating one of the other VAX computers, use CSA1 for device-name.

   $ RUN SYS$SYSTEM:SYSGEN SYSGEN> CONNECT CONSOLE SYSGEN> EXIT $ EXCHANGE DIRECTORY device-name:VMB.EXE Directory of RT-11 volume TINES$CSA1: 13-NOV-2000 18:40 VMB.EXE 80 13-NOV-2000 Total of 1 file, 80 blocks. Free space 43 blocks, largest 23.

   
   If the size of the current VMB, plus the free space, does not equal at least 120 blocks, delete unneeded files on the console until you have 120 blocks available. In the above example, the size of the current VMB.EXE (80 blocks) plus the free space (43 blocks) equals 123 blocks, so files do not have to be deleted.

3. Enter the following command and press Return:

   $ @SYS$UPDATE:UPDATE_CONSOLE.COM

4. If you are updating the console media for a VAX 8600 or VAX 8650 computer, the new VMB.EXE is copied onto the console media.
   If you are updating the console media for one of the other VAX computers, the procedure uses the EXCHANGE procedure to copy the contents of the existing console media, merge the new files onto the copy of the console media, and create a new version of the console media. When the computer is ready to create the new version, it displays a message asking you to insert a scratch tape cassette or diskette. Take out the original console media and insert a new one.

VAX 9000 computers use a special version of VMB.EXE named VMB9AQ.EXE. The upgrade procedure automatically copies a new version of this file to the console hard disk. However, if for some reason you need to update the console hard disk, use the UPDATE_CONSOLE.COM command procedure described for the VAX--11/730, 750, 780, 785 and VAX 8200, 8250, 8300, 8350, 8600, and 8650 computers. The device name for the VAX 9000 console hard disk is CSA1.

8.10 Decompressing the System Libraries

Decompressing the system libraries gives the system faster access to the libraries. You can decompress all the system libraries or just some of them. Table 8-1 gives the approximate number of blocks consumed by each library after decompression.

Table 8-1 Sizes of Decompressed System Libraries

Library	Blocks	Library	Blocks
HELPLIB.HLB	9108	EDFHLP.HLB	102
STARLET.OLB	8442	TPUHELP.HLB	1038
VAXCCURSE.OLB	102	ACLEDT.HLB	102
VAXCRTL.OLB	477	INSTALHLP.HLB	102
VAXCRTLG.OLB	102	LATCP$HELP.HLB	240
DECCCURSE.OLB	102	MNRHELP.HLB	102
DECCRTL.OLB	183	PATCHHELP.HLB	102
DECCRTLG.OLB	102	PHONEHELP.HLB	102
ERFLIB.TLB	105	SDA.HLB	111
STARLETSD.TLB	4800	SHWCLHELP.HLB	150
MAILHELP.HLB	273	SYSGEN.HLB	393
EDTHELP.HLB	231	TECO.HLB	102
DBG$UIHELP.HLB	408	UAFHELP.HLB	372
DBG$HELP.HLB	1986	EVE$HELP.HLB	1197
EXCHNGHLP.HLB	117	EVE$KEYHELP.HLB	147
NCPHELP.HLB	537	STARLET.MLB	2502
ANLRMSHLP.HLB	102	LIB.MLB	2229
DISKQUOTA.HLB	102

The additional amount of disk space required to decompress all system libraries is about 13,500 blocks. To find out how much disk space you have, enter the following command and press Return:

$ SHOW DEVICE SYS$SYSDEVICE

8.10.1 How to Decompress Libraries

You execute the LIBDECOMP.COM command procedure to decompress the system libraries. To run LIBDECOMP, log in to the SYSTEM account, enter the following command, and press Return:

$ @SYS$UPDATE:LIBDECOMP.COM

The following information is displayed:

OpenVMS Library Decompression Utility 1 HELPLIB.HLB 14 NCPHELP.HLB 27 PHONEHELP.HLB 2 STARLET.OLB 15 SDA.HLB 28 LIB.MLB 3 ACLEDT.HLB 16 SHWCLHELP.HLB 29 STARLET.MLB 4 ANLRMSHLP.HLB 17 SYSGEN.HLB 30 STARLETSD.TLB 5 DBG$HELP.HLB 18 ANALAUDIT$HELP.HLB 31 SYS$STARLET_C.TLB 6 DBG$UIHELP.HLB 19 SYSMANHELP.HLB 32 ERFLIB.TLB 7 DISKQUOTA.HLB 20 TFF$TFUHELP.HLB 33 SYS$LIB_C.TLB 8 EDFHLP.HLB 21 EXCHNGHLP.HLB 34 VAXCCURSE.OLB 9 INSTALHLP.HLB 22 TPUHELP.HLB 35 VAXCRTL.OLB 10 LATCP$HELP.HLB 23 EVE$HELP.HLB 36 VAXCRTLD.OLB 11 MAILHELP.HLB 24 EVE$KEYHELP.HLB 37 VAXCRTLT.OLB 12 MNRHELP.HLB 25 UAFHELP.HLB 38 IMAGELIB.OLB 13 EDTHELP.HLB 26 TECO.HLB 39 VMS$VOLATILE_PRIVATE_INTERFACES.OLB A ALL libraries to be decompressed E EXIT this procedure * Enter letter or number(s) of libraries to be decompressed (Separate multiple entries with a comma):

Enter the appropriate letter or the numbers of the libraries you want to decompress. To decompress all libraries, the process takes approximately one half hour.

If you prefer, you can execute LIBDECOMP interactively or as a batch job. If you use either of these methods, you can decompress up to 8 libraries each time you execute LIBDECOMP by listing the names of the libraries you want to decompress as parameters on the command line. (You can decompress all the libraries by omitting the /PARAMETERS qualifier.) Be sure to separate the library names with commas and do not include the file extension. For example, to decompress the VAXCRTL.OLB, DISKQUOTA.HLB, and LIB.MLB libraries as a batch job, enter the following command:

$ SUBMIT/NOTIFY/PARAMETERS=(VAXCRTL, DISKQUOTA, LIB)- _$ SYS$UPDATE:LIBDECOMP

To decompress these same libraries interactively, enter the following command:

$ @SYS$UPDATE:LIBDECOMP VAXCRTL DISKQUOTA LIB

Note that, when you type the command for a batch job, you separate the library names with commas and enclose the list within parentheses. You do not use commas or parentheses on the interactive command line.

8.11 Testing the System with UETP

UETP, the user environment test package, is a software package that tests whether the OpenVMS VAX operating system is installed correctly. As part of the postupgrade procedure, you should run UETP to verify your upgrade.

Note that UETP needs at least 1200 free blocks on the system disk and is available only if you installed the optional save set VMS072.D. If you did not install the optional save set, you can add the UETP files to your system using VMSTAILOR. For information about using VMSTAILOR, see Chapter 10.

For complete information about UETP, refer to the OpenVMS System Manager's Manual, Volume 2: Tuning, Monitoring, and Complex Systems.

8.12 Increasing Free Space on the System Disk

This section describes how to increase the amount of free space on your system disk. You can gain free space by removing optional OpenVMS VAX files that you do not need from the system disk or by purging old versions of some system files.

8.12.1 Running the ANALYZE /DISK_STRUCTURE Utility

Certain disk structure inconsistencies may be introduced during the OpenVMS VAX upgrade operation. To check for these inconsistencies, enter the following command:

$ ANALYZE /DISK_STRUCTURE SYS$SYSDEVICE:

This command produces output in the following format:

Error opening QUOTA.SYS No such file File (2849,7,1) DCLTABLES.EXE;31 marked for delete File (4270,3,1) SYS.EXE;2 marked for delete File (5485,9,1) SYS$NETWORK_SERVICES.EXE;1 marked for delete

If quotas are not in use on the system disk, ignore the "No such file" message for QUOTA.SYS. Most inconsistencies (including "marked for delete") can be repaired by entering the following command:

$ ANALYZE /DISK_STRUCTURE /REPAIR SYS$SYSDEVICE:

8.12.2 Using VMSTAILOR and DECW$TAILOR

To remove files you do not need from the system disk, use VMSTAILOR. For example, if you are not running DECnet for OpenVMS, you do not need the network support files. For complete information about using VMSTAILOR to remove files, see Chapter 10.

If you are running DECwindows Motif, use DECW$TAILOR to add or remove DECwindows base support, workstation support, and fonts.

In most cases, you can purge the following OpenVMS system files to free space on your system disk. However, before you purge any of these files, read Appendix F to make sure you do not purge a file version you might want to keep.

SYS$SYSTEM:SHUTDOWN.COM SYS$SYSTEM:STARTUP.COM SYS$LIBRARY:ENCRYPSHR.EXE SYS$LIBRARY:*RTL*.EXE SYS$LIBRARY:*SHR.EXE SYS$MANAGER:EDTINI.EDT SYS$MANAGER:DBLSTRTUP.COM SYS$MANAGER:*.TEMPLATE SYS$EXAMPLES:XADRIVER.MAR SYS$LIBRARY:CDDSHR.EXE SYS$LIBRARY:EPC$FACILITY.TLB SYS$MESSAGE:EPC$MSG.EXE SYS$STARTUP:VMS$LAYERED.DAT

To purge a file, enter the PURGE command followed by the file specification. For example:

$ PURGE SYS$SYSTEM:SHUTDOWN.COM

8.13 Restoring Your System Password Dictionary

The OpenVMS VAX operating system screens potential passwords for acceptability. The DCL command SET PASSWORD takes the user's proposed password, converts it to lowercase (if necessary), and compares it to entries in a system dictionary. If the proposed password is found in the dictionary, it is rejected as a valid user password, and the user must suggest another. Many system managers modify the system password dictionary to include words of significance to their site.

During the upgrade, the procedure replaces the existing system password dictionary with a new one. If you had modified the dictionary and want to restore your local additions, you must merge the file containing your additions with the new system file.

To add your site-specific passwords to the new system password dictionary, enable SYSPRV and merge your local additions by entering the following commands, where LOCAL_PASSWORD_DICTIONARY.DATA is the file that contains your additions:

$ SET PROCESS/PRIVILEGE=SYSPRV $ CONVERT/MERGE/PAD LOCAL_PASSWORD_DICTIONARY.DATA - _$ SYS$LIBRARY:VMS$PASSWORD_DICTIONARY.DATA

8.14 Customizing DECwindows Support Software

If you have installed DECwindows support software, there are several steps that you can take to customize the DECwindows environment. Depending on your configuration, DECwindows customization tasks include the following:

• Customizing the server startup
• Using the Transmission Control Protocol/Internet Protocol (TCP/IP) as a DECwindows transport
• Using transports for DECwindows other than those supplied by Compaq

Go to Chapter 9 for complete instructions for customizing your DECwindows support software.

After you complete the tasks described in Chapter 9, return to this chapter to continue with the remaining postupgrade tasks.

8.15 Preparing to Use the OpenVMS Management Station

The OpenVMS Management Station client/server software provides OpenVMS system management capabilities through a client application on a personal computer (PC) running Microsoft Windows.

When you upgraded your OpenVMS system, the OpenVMS Management Station server files were automatically installed on your OpenVMS system disk. However, to obtain complete support, you had to select the OpenVMS Management Station client software files during the OpenVMS upgrade procedure. Those files are required for creating the installation media that you use to install the client software on your PC.

Appendix G provides complete instructions for preparing your OpenVMS system and your PC to run the OpenVMS Management Station software.

Back up your system disk and then use either the VMSINSTAL command procedure or the POLYCENTER Software Installation utility to install layered products on your system. If the system contained Compaq TCP/IP Services for OpenVMS previous to the upgrade, you must reinstall it now.

For additional information about installing layered products, see the OpenVMS System Manager's Manual.

8.17 Backing Up the System Disk

Compaq recommends that you protect your work by performing the following operations:

• Use SYS$UPDATE:CONSCOPY.COM to back up the console media (if applicable).
• Make a standalone BACKUP kit on removable media and on the system disk.
  If your console media is a TU58 tape cartridge or an RX01 diskette, use the standalone BACKUP copy you made before you began the upgrade. (See Section 5.4.2.)
• Back up the system disk.

For complete information about these operations, refer to the upgrade and installation supplement for your VAX computer.

	privacy and legal statement
6630PRO_012.HTML