Updated: 11 December 1998 |
OpenVMS VAX
Version 7.2 Upgrade and
Installation Manual
Previous | Contents | Index |
UETP, the user environment test package, is a software package that tests whether the OpenVMS VAX operating system is installed correctly. As part of the postupgrade procedure, you should run UETP to verify your upgrade.
Note that UETP needs at least 1200 free blocks on the system disk and is available only if you installed the optional save set VMS072.D. If you did not install the optional save set, you can add the UETP files to your system using VMSTAILOR. For information about using VMSTAILOR, see Chapter 10.
For complete information about UETP, refer to the OpenVMS System Manager's Manual: Tuning, Monitoring, and Complex Systems.
8.12 Increasing Free Space on the System Disk
This section describes how to increase the amount of free space on your
system disk. You can gain free space by removing optional OpenVMS VAX
files that you do not need from the system disk or by purging old
versions of some system files.
8.12.1 Running the ANALYZE /DISK_STRUCTURE Utility
Certain disk structure inconsistencies may be introduced during the OpenVMS VAX upgrade operation. To check for these inconsistencies, enter the following command:
$ ANALYZE /DISK_STRUCTURE SYS$SYSDEVICE: |
This command produces output in the following format:
Error opening QUOTA.SYS No such file File (2849,7,1) DCLTABLES.EXE;31 marked for delete File (4270,3,1) SYS.EXE;2 marked for delete File (5485,9,1) SYS$NETWORK_SERVICES.EXE;1 marked for delete |
If quotas are not in use on the system disk, ignore the "No such file" message for QUOTA.SYS. Most inconsistencies (including "marked for delete") can be repaired by entering the following command:
$ ANALYZE /DISK_STRUCTURE /REPAIR SYS$SYSDEVICE: |
To remove files you do not need from the system disk, use VMSTAILOR. For example, if you are not running DECnet for OpenVMS, you do not need the network support files. For complete information about using VMSTAILOR to remove files, see Chapter 10.
If you are running DECwindows Motif, use DECW$TAILOR to add or remove DECwindows base support, workstation support, and fonts.
Files installed on alternate devices cannot be tailored. |
In most cases, you can purge the following OpenVMS system files to free space on your system disk. However, before you purge any of these files, read Appendix F to make sure you do not purge a file version you might want to keep.
SYS$SYSTEM:SHUTDOWN.COM SYS$SYSTEM:STARTUP.COM SYS$LIBRARY:ENCRYPSHR.EXE SYS$LIBRARY:*RTL*.EXE SYS$LIBRARY:*SHR.EXE SYS$MANAGER:EDTINI.EDT SYS$MANAGER:DBLSTRTUP.COM SYS$MANAGER:*.TEMPLATE SYS$EXAMPLES:XADRIVER.MAR SYS$LIBRARY:CDDSHR.EXE SYS$LIBRARY:EPC$FACILITY.TLB SYS$MESSAGE:EPC$MSG.EXE SYS$STARTUP:VMS$LAYERED.DAT |
To purge a file, enter the PURGE command followed by the file specification. For example:
$ PURGE SYS$SYSTEM:SHUTDOWN.COM |
The OpenVMS VAX operating system screens potential passwords for acceptability. The DCL command SET PASSWORD takes the user's proposed password, converts it to lowercase (if necessary), and compares it to entries in a system dictionary. If the proposed password is found in the dictionary, it is rejected as a valid user password, and the user must suggest another. Many system managers modify the system password dictionary to include words of significance to their site.
During the upgrade, the procedure replaces the existing system password dictionary with a new one. If you had modified the dictionary and want to restore your local additions, you must merge the file containing your additions with the new system file.
To add your site-specific passwords to the new system password dictionary, enable SYSPRV and merge your local additions by entering the following commands, where LOCAL_PASSWORD_DICTIONARY.DATA is the file that contains your additions:
$ SET PROCESS/PRIVILEGE=SYSPRV $ CONVERT/MERGE/PAD LOCAL_PASSWORD_DICTIONARY.DATA - _$ SYS$LIBRARY:VMS$PASSWORD_DICTIONARY.DATA |
If you have installed DECwindows support software, there are several steps that you can take to customize the DECwindows environment. Depending on your configuration, DECwindows customization tasks include the following:
Go to Chapter 9 for complete instructions for customizing your DECwindows support software.
After you complete the tasks described in Chapter 9, return to this
chapter to continue with the remaining postupgrade tasks.
8.15 Preparing to Use the OpenVMS Management Station
The OpenVMS Management Station client/server software provides OpenVMS system management capabilities through a client application on a personal computer (PC) running Microsoft Windows.
When you upgraded your OpenVMS system, the OpenVMS Management Station server files were automatically installed on your OpenVMS system disk. However, to obtain complete support, you had to select the OpenVMS Management Station client software files during the OpenVMS upgrade procedure. Those files are required for creating the installation media that you use to install the client software on your PC.
Appendix G provides complete instructions for preparing your OpenVMS system and your PC to run the OpenVMS Management Station software.
If you did not select the optional OpenVMS Management Station client software files during the installation or upgrade, you must add these files to your OpenVMS system disk before you follow the instructions in Appendix G. Use the OpenVMS Version 7.2 distribution media and VMSTAILOR to add the OpenVMS Management Station files to your system. (For information about using VMSTAILOR, see Chapter 10.) |
Back up your system disk and then use either the VMSINSTAL command procedure or the POLYCENTER Software Installation utility to install layered products on your system. If the system contained DIGITAL TCP/IP Services previous to the upgrade, you must reinstall it now.
For additional information about installing layered products, see the
OpenVMS System Manager's Manual.
8.17 Backing Up the System Disk
Compaq recommends that you protect your work by performing the following operations:
For complete information about these operations, refer to the upgrade
and installation supplement for your VAX computer.
8.18 Running AUTOGEN
When you upgraded the OpenVMS VAX operating system, the procedure executed AUTOGEN to set the values of system parameters and the sizes of the page and swap files according to the system's workload.
In many cases, AUTOGEN can improve system performance by using dynamic feedback information from the running system. As a postinstallation task, you should run AUTOGEN again using the feedback mechanism to make further adjustments to system parameters.
When AUTOGEN runs after an upgrade, it uses the parameter values in SYS$SYSTEM:MODPARAMS.DAT. Note that hardcoded values in MODPARAMS.DAT affect AUTOGEN's calculations of the feedback parameters. For AUTOGEN to properly calculate minimum values, you should replace the hardcoded values in MODPARAMS.DAT with MIN_ values. The MIN_ prefix specifies the minimum value to which a parameter can be set by AUTOGEN.
If you are not satisfied with the parameter settings calculated by AUTOGEN, you can modify the parameter values by editing MODPARAMS.DAT as explained in the OpenVMS System Manager's Manual: Tuning, Monitoring, and Complex Systems.
After you have upgraded the operating system, run AUTOGEN again using the following procedure:
For the VAX 9000 computer, AUTOGEN's initial parameter calculations are conservative. To obtain parameter values that match your system workload, you can run AUTOGEN in feedback mode a number of times. For more information, refer to the upgrade and installation supplement for your VAX 9000 computer. |
For information about using AUTOGEN, refer to the OpenVMS System Manager's Manual: Tuning, Monitoring, and Complex Systems.
8.19 Postupgrade Checklist
Use the following checklist to make sure you perform all the necessary postupgrade tasks.
This chapter describes how you can customize DECwindows support software. The DECwindows components provided on the OpenVMS VAX kit supply DECwindows base support and workstation support files only. If you have not installed either of these DECwindows components on your system, skip this chapter.
Depending on your configuration, DECwindows customization tasks include the following:
Note that the OpenVMS VAX operating system no longer includes the VMS
DECwindows product. To get full DECwindows support, you must also
install the separate DECwindows Motif for OpenVMS VAX layered product,
which supports both the Motif and XUI environments.
9.1 Customizing the Server Startup
By default, the DECwindows server no longer logs successful
connect/disconnect messages to the DECW$SERVER_#_ERROR.LOG file. To
enable these messages, define the symbol DECW$SERVER_CONNECT_LOG in the
DECW$PRIVATE_SERVER_SETUP.COM file to be "T" and restart the server.
Note that abnormal or unsuccessful connect/disconnect messages are
still logged by the server.
9.1.1 Assumptions
The startup command procedures automatically determine most of the configuration variables for the DECwindows display server. However, there are items that the command procedures cannot determine, so they make the following assumptions:
If any of these assumptions is incorrect, you must override them as follows:
$ DECW$SERVER_DENSITY == "100" |
$ DECW$SERVER_DENSITY == "75" |
$ DECW$COLOR == "FALSE" $ DECW$BITONAL == "FALSE" |
nn-nnnnn-xx. |
Dialect | Model | DECwindows Keymap Name |
---|---|---|
Austrian/German | LK201-(AG,LG,BG,MG) | AUSTRIAN_GERMAN_LK201LG_DP |
AUSTRIAN_GERMAN_LK201LG_TW | ||
LK201-(NG,PG) | AUSTRIAN_GERMAN_LK201NG_DP | |
AUSTRIAN_GERMAN_LK201NG_TW | ||
LK401-(AG) | AUSTRIAN_GERMAN_LK401AG_TW | |
Belgian/French | LK201-(AP,LP,BP,MP) | BELGIAN_FRENCH_LK201LP_DP |
BELGIAN_FRENCH_LK201LP_TW | ||
Belgian/French | LK401-(AP) | BELGIAN_FRENCH_LK401AP_DP |
BELGIAN_FRENCH_LK401AP_TW | ||
British | LK201-(AE,LE,BE,ME) | BRITISH_LK201LE_DP |
BRITISH_LK201LE_TW | ||
British | LK401-(AA,PA) | BRITISH_LK401AA_DP |
BRITISH_LK401AA_TW | ||
Canadian/French | LK201-(AC,LC,BC,MC) | CANADIAN_FRENCH_LK201LC_DP |
CANADIAN_FRENCH_LK201LC_TW | ||
Canadian/French | LK401-(AC,LC,BC,MC) | CANADIAN_FRENCH_LK401AC_DP |
CANADIAN_FRENCH_LK401AC_TW | ||
Czech | LK401-(BV) | CZECH_LK401AV |
Danish | LK201-(AD,LD,BD,MD) | DANISH_LK201LD_DP |
DANISH_LK201LD_TW | ||
LK201-(ED,RD,FD) | DANISH_LK201RD_DP | |
DANISH_LK201RD_TW | ||
Danish | LK401-(AD,LD,BD,MD) | DANISH_LK401AD_DP |
DANISH_LK401AD_TW | ||
Dutch | LK201-(AH,LH,BH,MH) | DUTCH_LK201LH_DP |
DUTCH_LK201LH_TW | ||
LK201-(NH,PH) | DUTCH_LK201NH | |
LK401-(NH,PH) | DUTCH_LK401AH | |
Finnish | LK201-(AF,LF,BF,MF) | FINNISH_LK201LF_DP |
FINNISH_LK201LF_TW | ||
LK201-(NX,PX) | FINNISH_LK201NX_DP | |
FINNISH_LK201NX_TW | ||
Finnish | LK401-(AF,LF,BF,MF) | FINNISH_LK401AF_DP |
FINNISH_LK401AF_TW | ||
Flemish | LK201-(AB,LB,BB,MB) | FLEMISH_LK201LB_DP |
FLEMISH_LK201LB_TW | ||
Flemish | LK401-(AB,LB,BB,MB) | FLEMISH_LK401AB_DP |
FLEMISH_LK401AB_TW | ||
Hungarian | LK401-(BQ) | HUNGARIAN_LK401_BQ |
Icelandic | LK201-(AU,LU,BU,MU) | ICELANDIC_LK201LU_DP |
ICELANDIC_LK201LU_TW | ||
Italian | LK201-(AI,LI,BI,MI) | ITALIAN_LK201LI_DP |
ITALIAN_LK201LI_TW | ||
Italian | LK401-(AI,LI,BI,MI) | ITALIAN_LK401AI_DP |
ITALIAN_LK401AI_TW | ||
North American | LK201-(AA,LA,BA,MA) | NORTH_AMERICAN_LK201LA |
North American | LK401-(AA,LA,BA,MA) | NORTH_AMERICAN_LK401AA |
Norwegian | LK201-(AN,LN,BN,MN) | NORWEGIAN_LK201LN_DP |
NORWEGIAN_LK201LN_TW | ||
LK201-(EN,RN,FN) | NORWEGIAN_LK201RN_DP | |
NORWEGIAN_LK201RN_TW | ||
Norwegian | LK401-(AN,LN,BN,MN) | NORWEGIAN_LK401AN_DP |
NORWEGIAN_LK401AN_TW | ||
Polish | LK401-(BP) | POLISH_LK401_BP |
Portuguese | LK201-(AV,LV,BV,MV) | PORTUGUESE_LK201LV |
Portuguese | LK401-(AV,LV,BV,MV) | PORTUGUESE_LK401AV |
Russian | LK401-(BT) | RUSSIAN_LK401_BT |
Slovakian | LK401-(CZ) | SLOVAK_LK401_CZ |
Spanish | LK201-(AS,LS,BS,MS) | SPANISH_LK201LS_DP |
SPANISH_LK201LS_TW | ||
Spanish | LK401-(AS,LS,BS,MS) | SPANISH_LK401AS_DP |
SPANISH_LK401AS_TW | ||
Swedish | LK201-(AM,LM,BM,MM) | SWEDISH_LK201LM_DP |
SWEDISH_LK201LM_TW | ||
LK201-(NM,PM) | SWEDISH_LK201NM_DP | |
SWEDISH_LK201NM_TW | ||
Swedish | LK401-(AM,LM,BM,MM) | SWEDISH_LK401AM_DP |
SWEDISH_LK401AM_TW | ||
Swiss/French | LK201-(AK,LK,BK,MK) | SWISS_FRENCH_LK201LK_DP |
SWISS_FRENCH_LK201LK_TW | ||
Swiss/French | LK401-(AK,LK,BK,MK) | SWISS_FRENCH_LK401AK_DP |
SWISS_FRENCH_LK401AK_TW | ||
Swiss/German | LK201-(AL,LL,BL,ML) | SWISS_GERMAN_LK201LL_DP |
SWISS_GERMAN_LK201LL_TW | ||
Swiss/German | LK401-(AL,LL,BL,ML) | SWISS_GERMAN_LK401AL_DP |
SWISS_GERMAN_LK401AL_TW | ||
Combined US/UK | LK201-(EE,RE,PE) | UK_LK201RE |
US_LK201RE | ||
Combined US/UK | LK401-(EE,RE,PE) | UK_LK401AA |
US_LK401AA |
Previous | Next | Contents | Index |
Copyright © Compaq Computer Corporation 1998. All rights reserved. Legal |
6521PRO_012.HTML
|